PDW7300J01CC General Electric Dishwasher - Instructions

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

I watched the video that came with email on part. Gave instructions on how to. Thank you !

Unscrew the old one and screw in the new one.

Called repairman: announced that the drain pump was gone. Did not seem right. Went to the website. Found what I was looking for. 49% of the time it was a check-valve issue; only 26% of the time was the pump the problem. Took the unit from under the counter; got it on its side; removed the drain pump. Found my first check-valve, but thediagram showed a second lower one toward the sump. Having located both and purchased two valves and and the lower holder piece, I was ready to finish the job. Quarter-inch nut driver and a screw driver and the valves were in and the drain pump re-installed. Most difficult in my case was getting the dw back into its spot and lashed down! Thanks for the good guidance!

Put new basket in, threw old one away

Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

First removed the eight philips head screws that hold the outside bottom door cover, to get access to the module. Then removed the two wires and the ten screws holding the module in place. Put the new module back in, reconnected the wires, and re-tighten everything. Did not have to use the bracket and cap.

After I unscrewed it from the counter and took off the front panel I first went to the garage to turn off the power to the dishwasher. I then pulled it out a little bit at a time. I didn't want to take apart any hoses or unplug electrical wires from connectors if I didn't have to. I then looked underneath and noticed that only one pulley spring was off and the plastic piece was broken. So when I received it in the part in the mail I took of the plastic part from the pulley. I just reused the original wire pully. I reached back with the spring to hook it back on with some difficulty and then hooked the piece back on and it was done. I placed everything back and switched the power on and its good to go. Nice job to do myself and watch a Youtube video on how to do it.

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.

Installed new lower rack wheel kit

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS