GSD4300L01BB General Electric Dishwasher - Instructions

I looked at your web sight and saw how to repair dishwasher.

This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!

repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit

After two repair people were unable to solve the problem, I read similar stories in your forum and decided to replace the check value as a last ditch effort. Looking at your diagrams it seemed like an easy repair. Removed four screws with nutdriver and replaced value by hand. Ran washer three times and water drained completely. Still puzzled that this wasn't the first thing a repair person would check.
Websight very helpful.

The replacement of the motor and pump assembly went smoothly and without difficulty however this did not fix the problem. It then appeared that the inlet water valve was not operating properly, so this part was ordered and instlled, a very simple proceedure that could be done witrhout removving fthe dishwasher from its cabinet. -- Again failure to run -- the timer assembly and electronic panel were then removed and examined. The control panel had no visible defects, so the timer assemblyand its cover was removed and examined . Uing a variable power supply the drive motor for the timer was energized and tested. As the motor ran properly the electrical switching contacts were then carfully checked, it was discovered that one contact set was heavily pitted and burned. These contacts were carefully cleaned and pollished with 1000 grit sanding paper. The actuator leaves were examined and two sets were found to be slightly out of alignment. The leaves on these sets were bent slightly to insure they were in line with the rest of the leaf serts. It was then noted that the rotating leaf('s) actuator had a home position indicated by a molded depression at one location and the motor was energized using approximately 5 volts ( a nine volt battery could also be used as a poer supply) observing prolper polarity to run the rotator until the home position was established and the actuator rods paul dropped into this depression. The assembly was then replaced in the diswasher using care to make sure that the actuation arm and spring were positioned properly weith the arrow end of the arm located in the recesss of of the rotating timer disk use care in placing the assembly and do not lose the sping which attaches to a mounting post and the arm. You may want to take a picture of the spring and arm locations when you rwmove the timer assembly to properly re-assemble all components, the repaired unit was placed back in its cabinet and a full cycle run to establish proper operation. And unit checked ok! Some of these proceedures are not for the weak of heart. I am a retired engineer who has been repairing my own equipment since graduation. .

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

ordered and received parts. unplugged electricity and drain and water supply turned dishwaser upside down for ease of access. removed clamps usin 1/4 and 5/16 nut drivers and phillips head screw driver to undo bracket clamps old parts and replaced and as per directions using two pair of adjustable pliers one to hold motor shaft and other pair to remove cutting blade. replaced impeller and blade ttaking care to keep track of screws nuts and bolts and older parts to make sure of assembly. turning dishwasher upside down makes for easy parts instalment. PAY CLOSE ATTENTION TO DISASEMBLY AND PUT TOGETHER IN REVERSE ORDER GOOD LUCK parts ordered to replace solonoid kit as it feels hot and still have burning bakelite odor.

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.

Unscrewed unit from counter and loosened legs using adjustable supports under dishwasher. After switching off water under sink and power at circuit breaker, removed motor and pump assembly and replaced with repair kit.

The most difficult part was removing the old wheels. The plastic coating on the rack had come off, leaving the metal exposed. The wheels had rusted on - that's why they wouldn't roll. Once we got them off with pliers, hammer, screwdriver and basically everything in the tool chest, we were home free. Installing the new wheels and axles was easy.

After checking to make sure the filter wasn't clogged I removed the faceplate and, poking around a bit realized that the solenoid that actuates the drain valve was jammed. Removing it was was simply a matter of removing a pin and two screws. I reattached the new part, the only difficult part was holding the part in place while reattaching a few springs. Closed it up and its working like a champ.

I went to your site and check all the diagrams and then read the postings from others. I turned off the electrical breaker then took off the lower cover of the dishwasher. After disconnecting the water and electricial connections I was able to remove the 2 screws holding the unit in place and it came right out. I turned the unit over and was able to just remove the old part and put the new part in place. The whole job took me about one hour but I had never worked on a dishwasher before. Your site made the repair very easy to do on my own.

I replaced the drain solenoid which was about $35 dollars. It consisted of a couple of springs, a hanging bracket, a plastic part and couple of screws to fasten the bracket and the solenoid of course. My dishwasher now drains the water. Much easier fix than i thought it would be.