GLD5606V15BB General Electric Dishwasher - Instructions

Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled

First, I pulled out the drain hose under my sink that connected the dishwasher to the disposal and overflow valve. I drained all the water out of the dishwasher and ran it to see if it would drain. It did not. So I drained the water out again and then pushed the hose back in the hole it came through from the dishwasher. My water for the dishwasher is hooked up under my sink as well so I pushed the excess length of hose through the same hole to give me enough play to get the dishwasher out. Other people may need to disconnect the water first, but regardless, turn off the water at source under the sink.
After concluding that the drain pump was running at the end of the wash cycle (I could hear a slight buzzing sound), I figured that the timer was working as it was telling the pump to run and determined that the pump was not working properly.
I unscrewed the screws that held my kick plate on below the dishwasher door. Turned off power. Took a digital pic of the wiring so I could refer to it when putting back in. Unhooked 3 wires that supplied power.
Then I unscrewed the screws that held my dishwasher under the countertop (2 small screws).
I gently pulled out the dishwasher until it was free of the space it was in under the counter. I put two 3ft 2x4's on the kitchen floor with a few towels under to soak up the extra water that was unable to drain ealier. I turned the dishwasher on its side so that the bottom was now visible.
I then took a digital pic of the broken drain pump all hooked up so I could refer to it when putting the replacement in. After removing the two wires hooked up to the pump and loosening both sides of the pump from the drain and drain hose, I removed the broken pump.
From that point, I installed the new pump and tightened both ends securely, hooked up the wires, picked up the dishwasher on it's bottom, hooked up the three wires for power supply and gently put dishwasher back under counter. I had to pull the drain hose gently and water hose so they would not kink behind the dishwasher. I hooked up the drain hose to the disposal and overflow valve, turned on the water and the power and ran a test cycle. Good to go!

replaced it

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!

removed two bottom screws on inside door panel and slid seal onto spline, reinstalled screws. Job done

Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.

Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.

I replaced the broken/cracked soap and Jet Dry dispenser (i.e. MODULE RINSE AND CAP ASM - part #PS1481889). (Water was leaking into the soap holder and hardening the soap into a lump before the door would open, rendering the soad useless).

Steps:

1) Unplugged the dishwasher.
2) Unscrewed the 6 screws holding the front stainless steel panel to the plastic door; set aside panel and insulation.
3) Unplugged two wires from small electric motor in broken ASM.
4) Unscrewed 6 screws holding ASM in place; easily slid out of door.
5) Slid in replacement ASM and put 6 screws back in (tightened snugly to make slightly warped door bend to new ASM).
6) Plug back in two wires into new ASM.
7) Re-attached stainless steel cover to door (having a 2nd person hold this in place while screwing would've helped).

All done - works like a charm! No more dirty dishes because the soap didn't work right...

Bottom line: If you have a phillips head screwdriver, you can do this repair. Easy to do.

Once we ordered both the "Stud Roller" and "Roller Lower Rack" the repair was simple.

The previous studs mostly disitegrated, so their removal was not an issue. The wheels pulled off easily.

I recomend getting new studs and rollers for all of the wheels on your rack. For me, that was 8 wheels and 8 studs.

First, take the rack out and flp it upside down in a convenient working space. Next, remove all of the old wheels and studs from the rack and discard. Then, snap the new wheels on to the new studs. Next, atached the stud (with the wheel) to each of the 8 spots on the rack. Put the rack back in the dishwasher and walla!

I can't beive that I waited almost two years to make this simple repair.

1. remove old basket. 2 Place new basket.. Done

Installing the gasket took about 45 seconds. It actually took more time to scrub the area clean prior to installing. One quick trick I found was to fold the replacement gasket in two, and use that mark to center the gasket and press it in from there. That way you don't have any guesswork as to how much slack to allow for when starting.

First, I took off all the pipe clamps and retaining brackets. Then, I pried it out of there. One of the tabs holding one of the other bits to the body got busted, but it didn't matter, as it is held on very well just by the pipe clamp connection. I stuck the new one in and re-attached all the hoses. The GIANT complication was that a new floor had been installed over the old floor, right up against the kick plate- so in order to remove the dishwasher, I had to slice open the counter, as the new floor prevented sliding it out. To prevent the problem recurring, I spray painted over the sump inlet to make it taste worse. This is the downside of a cat door.

Took screws out of door. Slid bottom seal off and slid new one on.

Remove screws holding old hose. Attach clamp to new hose with nut driver. Tighten hose and clamp around attachment.

Easy as cake. Perfect part!

i looked on this website and found out which part was the drain pump. the pump was fastened to a drain hose, the dishwasher and power supply. unhooked power supply, noting which color wire belonged where. loosened the hose from the pump, got the new pump, installed. viola!