GSD4360L01SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- LINDY from COLORADO SPRINGS, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Inch Of Clean Water Left In Machine After Each Cycle
First let me say, it's so easy even a caveman can do it. I removed the water out of the bottom. Then I removed the cover in the very back of the machine with a wrench. As soon as I did that, I could see the piston. Next, I twisted the white piston out with my fingers (this was the hardest part). I could see the piston had partially disintigrated. I ordered a new one, had it delivered in a few days, and put it all back in reverse. It took minutes. Thanks to the guy that posted his story, I was able to fix mine for $18.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Broggie from Burlington, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill Cap Just Keep Turning, Not Locking In Place
I Just Open Door And Put Fill Cap In And Turn That It
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from Allendale, MI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher would not drain completly after each cycle
removed screen at back of dishwasher from the inside. Twisted piston & nut assembly out by hand and replaced with new one. Very, very simple. Dishwasher works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chloe from Salisbury, NC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dishwasher was not drainig completly after completing the cycles
Followed the simple instructions to unscrew the old unit and replace with the new one. The unit was easily located on a diagram on the internet and the website instructions for removal were spot on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from SOULSBYVILLE, CA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Dishwasher Has Water Left in the Bottom
Removed filter screen with the socket set, removed the piston and nut assembly with pliers, and installed the new piston and nut assembly. Put filter screen back in with hex head screws. During the process, I opened the float regulator and cleaned it out too. Water backup problems solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John W. from SEMMES, AL
- Parts Used:
- WD24X10018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher not draining and not getting dishes completely clean.
First I removed the bottom dishwasher rack. Using a 1/4" nutdriver I removed (4) 1/4" screws from the drain cover that is inside the dishwasher all the way in the back. This will allow you to get to the piston and nut assembly which was easily removed with no tools by simply grasping and unscrewing. Used a wash cloth to wipe "gunk" from around the threads. I then screwed the new piston and nut assembly in place. Used no tools to tighten, just "snug up" by hand. The seal on my old piston and nut assembly was 50 percent gone, not sealing at all. I guess the years had taken their toll. This solved my problem. The dishwasher washes and drains as it should. Super easy fix. Took me about 10 minutes to do the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from ST LOUIS PARK, MN
- Parts Used:
- WD24X10018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishes were not coming out clean and water was standing after the wash cycle was complete.
Removed filter/screen by unscrewing 2 screws with a nut driver and then unscrewed the old Piston and Nut assembly and simply screwed in the new part. Problem solved and my dishes are much cleaner and the water is draining out completely. Easy fix for this frustrating problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Medford, NY
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
water was not draining
Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from LYNN, MA
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Fill Cap broke off left portion in door
Used drill and easy out to remove broken part, then put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Rocklin, CA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher was not draining completely
Just remove the 4 screws at the lower rear inside the washer to remove screen holder...then unscrew the Piston and Nut Assembly by hand. Put in the new unit, reattach the screen holder with the 4 screws...and the job is done. Probably takes less than 5 minutes....very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Franklin, TN
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Aid Fill Cap missing from dishwasher in condo I just bought.
Opened package, removed cap and screwed it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Franklin, TN
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Had leak in the dishharge valve
The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Bastrop, TX
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Old pump was making noise and leaking.
Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from bensalem, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dishwasher would not drain.
REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.
Was this instruction helpful to you?
Thank you for voting!