GDF630PGM6WW General Electric Dishwasher - Instructions

The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.

The old gasket pulled right out with no tools needed,
The new gasket went in the same way.

Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.

Next Steps:
When the bottom gasket gets here I will replace that and it should be as good as new.

Super easy repair, just removed the old latch and replaced it with the new one.

the hardest part was removing the door from the face of the washer. Getting the door off required accessing the sides, so I had to lower the feet so it would slide out of the recess it sits in.
Disconnecting the springs for the door was straight forward and simple. once those were disconnected, it lifted off the hinges easily. The seals themselves were simply press-fit into the recesses. the old ones pulled loose cleanly and easily.. the new ones pressed into place very simply and without any real effort.
Getting the door back on was a little problematic, mostly in getting the hinge pins to line up properly.. but once it settled in, it line up itself, and the springs were easily replaced. I re-leveled the dishwasher, and then ran it for a full cycle to ensure it wouldn't leak anymore.

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!

The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.

Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.

Simple answer- do not try to do this. GE makes you replace the entire door to replace this $3 part or call them and pay $100s to fix it. We decided to replace the entire dishwasher after we went through disassembly (there are no instructions on this) only to find out we could not fix without a brand new door.

Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.

Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!