GSD5720F01BB General Electric Dishwasher - Instructions

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.

I would use this service again if needed for additonal home appliances.

Thank you
Mr. Buddy King

The replacement of the motor and pump assembly went smoothly and without difficulty however this did not fix the problem. It then appeared that the inlet water valve was not operating properly, so this part was ordered and instlled, a very simple proceedure that could be done witrhout removving fthe dishwasher from its cabinet. -- Again failure to run -- the timer assembly and electronic panel were then removed and examined. The control panel had no visible defects, so the timer assemblyand its cover was removed and examined . Uing a variable power supply the drive motor for the timer was energized and tested. As the motor ran properly the electrical switching contacts were then carfully checked, it was discovered that one contact set was heavily pitted and burned. These contacts were carefully cleaned and pollished with 1000 grit sanding paper. The actuator leaves were examined and two sets were found to be slightly out of alignment. The leaves on these sets were bent slightly to insure they were in line with the rest of the leaf serts. It was then noted that the rotating leaf('s) actuator had a home position indicated by a molded depression at one location and the motor was energized using approximately 5 volts ( a nine volt battery could also be used as a poer supply) observing prolper polarity to run the rotator until the home position was established and the actuator rods paul dropped into this depression. The assembly was then replaced in the diswasher using care to make sure that the actuation arm and spring were positioned properly weith the arrow end of the arm located in the recesss of of the rotating timer disk use care in placing the assembly and do not lose the sping which attaches to a mounting post and the arm. You may want to take a picture of the spring and arm locations when you rwmove the timer assembly to properly re-assemble all components, the repaired unit was placed back in its cabinet and a full cycle run to establish proper operation. And unit checked ok! Some of these proceedures are not for the weak of heart. I am a retired engineer who has been repairing my own equipment since graduation. .

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.

I had a problem where the GE dishwasher would randomly stall upon startup due to a dead spot in the motor which prevented it from energizing. I removed the dishwasher's bottom access panel to inspect it and found that not only was the motor dead but it had a sizable leak emanating from the pump seal. I removed the dishwasher from under the cabinet area and turned it over to make it easier to replace the motor and pump assembly which only took a matter of minutes; the most difficult part of the repair being the reinstalling of the dishwasher. The replacement motor/pump assy was not only modified from the original parts but it is also much quieter than the original. I also have to commend PartSelect on their very speedy delivery which was only 2 days. All in all with a couple of minor modifications that was taken care of with the included parts the repair went very easy.

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

Used drill and easy out to remove broken part, then put in new one

The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.

I simply removed the bad part and reversed the process. It was very easy and a 12 year old could do it. Thanks for the online tips and recommendations. You saved me over 400.00 which is what a new unit would run. Plus installation. Many Thanks.

Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.

I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.

Opened package, removed cap and screwed it in place.