GSD2250F00CC General Electric Dishwasher - Instructions

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

Opened package, removed cap and screwed it in place.

Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)

Used drill and easy out to remove broken part, then put in new one

The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.

Recieved universal parts f/ pump & mtr assy. sorted them out, picked the ones I needed to complete my repair. Installed new assy, checked operation and was completly done in about an hour.

My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.

Unscrewed unit from counter and loosened legs using adjustable supports under dishwasher. After switching off water under sink and power at circuit breaker, removed motor and pump assembly and replaced with repair kit.

Turned off the electricity to the dishwasher,removed the old solenoid,and put the new one on(very easy),turned the electrical breaker back on.

Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.

I had a problem where the GE dishwasher would randomly stall upon startup due to a dead spot in the motor which prevented it from energizing. I removed the dishwasher's bottom access panel to inspect it and found that not only was the motor dead but it had a sizable leak emanating from the pump seal. I removed the dishwasher from under the cabinet area and turned it over to make it easier to replace the motor and pump assembly which only took a matter of minutes; the most difficult part of the repair being the reinstalling of the dishwasher. The replacement motor/pump assy was not only modified from the original parts but it is also much quieter than the original. I also have to commend PartSelect on their very speedy delivery which was only 2 days. All in all with a couple of minor modifications that was taken care of with the included parts the repair went very easy.

Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

After checking to make sure the filter wasn't clogged I removed the faceplate and, poking around a bit realized that the solenoid that actuates the drain valve was jammed. Removing it was was simply a matter of removing a pin and two screws. I reattached the new part, the only difficult part was holding the part in place while reattaching a few springs. Closed it up and its working like a champ.