GHDA485N10CS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nick from CARNATION,, WA
- Parts Used:
- WD26X10053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
dishes were not coming clean. I found the pump that sprays water was not running
I noticed the circulation pump was not operating. If I turned the motor with a screw driver it would start running. I replaced the pump and now the dishwasher works like new. Very easy to replace the pump but you will have to pull out the dishwasher and turn on its back. I was able to confirm the circulation pump was the problem by observing the motor not running when it should but it would run once I turned the inside motor parts(be careful!). I also had to replace the center sprayer which again was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from Spring, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel fell off dishwasher rack, landed on heating element and melted.
Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from OCALA, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost A Wheel For Dishwasher
Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHY from LAS VEGAS, NV
- Parts Used:
- WD26X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher was not draining
We pulled the dishwasher out completely, drained water that was in the dishwasher. Tilted the dishwasher and the part we needed to replace (Pump Drain Assembly) was in clear view. We used a screwdriver to take out a few screws and replaced the Pump Drain Assembly with the new one. Put the dishwasher back in and proceeded to wash dishes in the now fixed dishwasher. The part was very easy to change out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lori from MANHASSET, NY
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on our dishwasher were mis-shapen and broken
It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Surprise, AZ
- Parts Used:
- WD28X10384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced the bottom washer rack.
Just took out the old rack and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Salida, CA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Dishwasher did not fill.
Traced the problem back to the water valve. turned off the water. Disconnected the water inlet and outlet lines. removed the 2 mounting screws and unplugged the terminals.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Kearney, NE
- Parts Used:
- WD28X10177
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken "small" silverware holding lid
Replaced the entire basket and lids.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- norma from Sudbury, MA
- Parts Used:
- WD28X10384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the "fingers" in the lower rack were rusted through and sullying the dishes when cleaning
Just replaced the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Taylor from Scotia, NY
- Parts Used:
- WD22X10084, WD22X10047, WD22X10046, WD12X10109
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench set
Dishwasher wasn't cleaning properly
My dishwasher was doing a terrible job of cleaning. It was leaving food on dishes, and wasn't dissolving all the detergent. I replaced all the spray arms and the filter, as they seemed clogged, and god knows how old. It's a super easy repair, and the dishwasher now works as if it were brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vern from Orem, UT
- Parts Used:
- WD26X10053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noise, Poor cleaning
Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Lincoln, CA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Soap dispenser latch broke - never worked right
This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from MAYFIELD, UT
- Parts Used:
- WD12X10271, WD12X10401, WD03X10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cover, Interlock Heats Ups And Bends Causing Switch Problems
Ordered your new and improved interlock cover made with better plastic (thank you). Your new spring is also better. It's bigger and longer and is now the right size. (Thank you). Your parts are better than oem. The interlock is easy to get to. The oem one is black and you can see that it is bulged. The replacement one is gray speckled with white and black. You can see the improvement by just making a comparison. Just unclip the old one and clip in the new one. . Repace panel cover. Now it works and should work now for many a year. Thanks! Parts select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Westminster, MA
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
water inlet valve leaked
I cut the water off to the DW, unscrewed the water connection to the inlet valve, unplugged the electric connection, disconnected the black rubber line from the valve to the washer, removed the 2 screws holding the valve in place. Put the new valve on by doing the above backwards. I also used white thread tape on any connections that needed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Holland, PA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Metal cover broke off of lower spray arm and gluing didn't work.
Turned spray arm while lifting upward to remove the old part. Place new spray arm over the water outlet and turned with light downward pressure until properly seated.
It less time to do the repair than it took to open the box and unwrap the part!
It less time to do the repair than it took to open the box and unwrap the part!
Was this instruction helpful to you?
Thank you for voting!