PDW7800J10CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from HGHLNDS RANCH, CO
- Parts Used:
- WD15X10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Dishes Weren't Getting Clean At All
The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.
When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.
I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.
Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.
My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.
TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.
When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.
I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.
Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.
My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.
TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Waldwick, NJ
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Wheels kept falling off
Removed the old wheels and studs. Pressed on the new studs and wheels. Viola.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maurice, LA
- Parts Used:
- WD22X10084, WD22X10047, WD22X10046, WD12X10109
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dishes where not clean after washing
change the nozzles and filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MACKINAW, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Carlisle, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Palatka, FL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack was rusted out and missing most of the wheels.
Easiest repair ever. My new rack arrived in three days, opened the box and slid it in. Better quality than the original. Excellent service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Mashpee, MA
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the lower rack wheels had fallen off and melted
The best money I've spent on a repair. Easy. The lower rack now rolls in and out smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Woodstock, GA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
axle for wheel was broken
Popped the axle on to the wheel, then snapped it on to the lower drawer - done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Durango, CO
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
some wheels had broken, was really hard to move rack in and out.
I am NOT handy, but my husband was gone when the wheels and stud/axles came. I was able to replace all of them in about ten minutes with no tools. Easy and no more frustrations!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ILONA from AUSTIN, TX
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one wheel was missing, others kept on falling off
Just snapped studs and wheels together and put them into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Estelle from Queen Creek, AZ
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a rip in our tub gasket.
I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FAIRFIELD, CT
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holes in old dishwasher basket
The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from MECHANICSBURG, PA
- Parts Used:
- WD28X10013
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Regular and often use, just wear
Literally 1 minute to replace. They are perfect and an easy fix for split tongs on the wine glass holders
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Chandler, AZ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Due the the age of this dishwasher (13 years) both upper and lower racks were showing significant rusting.
This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carla from valdosta, GA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Food particles had started stopping up spray arm and get them out.
Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.
Was this instruction helpful to you?
Thank you for voting!