GSD4020Z00BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jackie from Hughes Springs, TX
- Parts Used:
- WD28X10232
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken tower
removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Chantilly, VA
- Parts Used:
- WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace upper rack in dishwasher
Remove end caps on the slides on the upper rack pulled old rack out put new rack in push end caps back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristine from Arboles, CO
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
the gasket was wider than the one replaced
I had to readjust the door latch to get the door to close
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Pasadena, CA
- Parts Used:
- WD27X10223, WD31X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
replace dishwasher door pannels
I am so pleased with Parts Select. I placed my order on Sunday night and the parts were here on Tuesday morning. the install went well except for a small handful of spare parts! Anyway it looks like new and runs with no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Burlington Twp., NJ
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
leaky pump
This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lakeport, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
cracked riser in spray arm
Ordered part Monday evening installed it on Wednesday afternoon. Required a pair of pump pliers to loosen old part, new part screwed in by hand. No leaks, no problems. Took longer to explain what caused the problem then it did to fix it. I explained to the owner that overloading the dishwasher was most likely the cause. Dishes can move or fall against the riser during wash, preventing it from dropping back down. Pulling the lower rack out with the riser bound up caused the part to crack. Thanks for the speedy delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Yucca Valley, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The smallest portion of the sprayer had been broken
Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Alpharetta, GA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher very noisy when washing/rinsing
Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark L from Dover, DE
- Parts Used:
- WD27X10223
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Panel looked lik an import. Holes did not line up with factory holes.
Held panel in place and drilled holes and installed drill screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Mesa, AZ
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking gasket
Removed old gasket, cleaned grooves, installed new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willcox, AZ
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking motor seal
Followed easy instructions and completed repair in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burl from Spring Valley, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Motor failure because of black power wire separation.
Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERREL from PORTLAND, OR
- Parts Used:
- WD28X31820
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Upper dish tray was rusted
Replaced the tray with a new one. Would have been no problem at all, if I had realized how the track end clip was supposed to go. I thought the release had to be pushed toward the lock, but it needs to be pushed away from it. This sounds confusing, but when you look at it, it may be more clear to you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergei from West Chester, PA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replace door gasket
Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Town of Tonawanda, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
motor fan broke
I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!
Was this instruction helpful to you?
Thank you for voting!