GDF550PGR3WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Chris from LAS VEGAS, NV
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower dishwasher rack was rusting out. The rubber/epoxy coating was coming off causing rack to rust out.
Removed the old lower rack and slide the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hooksett, NH
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish rack prongs rusted and broke off
It wasnt exactly the right lower dish rack to hold silverware holder. Instead of the trouble of sending it back we will use it. Silverware holder takes up some of the space for other dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SEBRING, FL
- Parts Used:
- WD22X33498, WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corinna from MOUNT AIRY, MD
- Parts Used:
- WD08X21894
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Door gasket needed to be replaced
Simple answer- do not try to do this. GE makes you replace the entire door to replace this $3 part or call them and pay $100s to fix it. We decided to replace the entire dishwasher after we went through disassembly (there are no instructions on this) only to find out we could not fix without a brand new door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OMAHA, NE
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack rusted out
Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from WINONA, MN
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old rack had rusted and broken tines
1. Take a picture of the old rack in the dishwasher! Just in case!
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.
Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.
Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from N HOLLYWOOD, CA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
old nasty gasket needed to be replaced
youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from SCHENECTADY, NY
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Door gasket at bottom of door was falling apart and leaking
1. Shut off circuit breaker power
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from VERO BEACH, FL
- Parts Used:
- WD28X34744, WD28X35779, WD12X10426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Deteriorated dishracks
Quite simple. Only disassembly/reassembly was the spray mechanism attached to the bottom of the Upper Rack. Snaps off old and on to new rack with no tools. On this dishwasher model, there is no hose assembly running to water port, but the spray assembly is instead a integrated tube with a male port that "plugs" into a female port on back of unit. Definitely get 2 end caps.
Only difference from original, is the design of the bottom rack. To fit such that the door closes, the silverware rack is at the back of the unit versus the front. Somewhat inconvenient. Can put silverware rack in front, but then less efficient for dishes.
Only difference from original, is the design of the bottom rack. To fit such that the door closes, the silverware rack is at the back of the unit versus the front. Somewhat inconvenient. Can put silverware rack in front, but then less efficient for dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from CHESAPEAKE, VA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating element broke off and burned a hole in rubber tube, leaking water.
Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Brambleton, VA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replace the middle flatware basket
So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from MASON, OH
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty Lower Rack
Removed lower rack, slid in new Rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francesca from PALM COAST, FL
- Parts Used:
- WD28X35779
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty upper rack
I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Praveen from Monroe Township, NJ
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
as better as it gets
the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PRAVEEN from MONROE TWP, NJ
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rusty DW Baskets
the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
PS12743260Manufacturer Part Number WD28X26099
PS12743260Manufacturer Part Number WD28X26099
Was this instruction helpful to you?
Thank you for voting!