XDF300PGN5BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from JAMESTOWN, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door did not latch, therefore would not operate
Replaced latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaRay from PRESCOTT, AZ
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
soap did not dispense correctly
Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from White City, OR
- Parts Used:
- WD19X27178
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dishwasher ticks when running, eventually got quiet and no water pressure from sprayers.
- Shut off breaker to dishwasher
- Shut off water to dishwasher
- Disconnect dishwasher drain hose at disposal
- Remove kick panel
- Remove junction box cover and disconnect wires
- Loose dishwasher mounting screws and slide dishwasher out
- Disconnect water inlet while sliding dishwasher out
- Flip dishwasher on its back
- Disconnect wash pump
- Rotate and pull to remove pump
- Install new pump, use small amount of dish soap to lubricate the seals.
Reverse order to install. There is a video online by another vendor for this exact job, but they included a lot of unnecessary steps. I did follow that video at first, and then realized that I didn't have to do 60% of it.
- Shut off water to dishwasher
- Disconnect dishwasher drain hose at disposal
- Remove kick panel
- Remove junction box cover and disconnect wires
- Loose dishwasher mounting screws and slide dishwasher out
- Disconnect water inlet while sliding dishwasher out
- Flip dishwasher on its back
- Disconnect wash pump
- Rotate and pull to remove pump
- Install new pump, use small amount of dish soap to lubricate the seals.
Reverse order to install. There is a video online by another vendor for this exact job, but they included a lot of unnecessary steps. I did follow that video at first, and then realized that I didn't have to do 60% of it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CLIFFSIDE PK, NJ
- Parts Used:
- WD22X33498, WD22X10090
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Kept falling off during use.
Just took old one off & install new one. Snaps on dish rack. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from NAPLES, FL
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SEBRING, FL
- Parts Used:
- WD22X33498, WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hooksett, NH
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish rack prongs rusted and broke off
It wasnt exactly the right lower dish rack to hold silverware holder. Instead of the trouble of sending it back we will use it. Silverware holder takes up some of the space for other dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OMAHA, NE
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack rusted out
Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from LAS VEGAS, NV
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower dishwasher rack was rusting out. The rubber/epoxy coating was coming off causing rack to rust out.
Removed the old lower rack and slide the new one in.
Was this instruction helpful to you?
Thank you for voting!