HTMX050EF3WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- gerald from ardmore, PA
- Parts Used:
- WR60X31522, WR60X46086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
evap.motor burned out
common sense,removed plate,removed mounting bracked,unplugged,reversed order,and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willard from HUTCHINSON, KS
- Parts Used:
- WR24X10231
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Getting the gasket into the tight groove.
Remove the fridge door and put it on the floor. Being able to apply lots of pressure helped get it into the tight groove. The corners were the hardest part. This requires strong "man" hands!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Downingtown, PA
- Parts Used:
- WD21X31899, WD13X10071, WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Doesn't complete dry cycle, no clean light, random noises as if door was closing
Removed toe kick. Removed door counter weights and placed door on soft surface. Removed two bolts(I was able to leave hinges in place) slid door panel down and off. Removed plastic snap fit cover and 4 bolts from UI board. Two of the stand-offs where broken, glued them back into place. Ensured jumpers were set to my model, snapped cover back in place and remounted door. The dishwasher now runs through the cycle and clean light but did not dry. That turned out to be a bad flood switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Brooklyn, NY
- Parts Used:
- WR71X10378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Not enough shelf space
At this time of the year our beach fridge is always full of food and drinks. Every time we want something it meant leaving the door open for extended time whlie moving things left, right and center. When the new shelf arrived I removed the food and drinks from the existing two shelves and moved them closer together. I then slipped in the new shelf and reloaded the food. Suffice to say the fridge stays open less and we are able to get at things without moving others. I wish I had thought to do this before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Old Town, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Handle
Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Richmond, KY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken dryer handle
My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from patterson, NY
- Parts Used:
- WR02X12149, WR60X31522, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Fan Motor was Noisy
4 screws in the freezer and the back panel came off then 2 more screws to take the motor off. I unpluged the old motor pluged in the new motor put the back panel back on and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from WILLISTON, ND
- Parts Used:
- WE04X20089
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Timer appeared to be broken. Turned all the way around without contacting anything.
Ordered new timer with overnight delivery and thought all was well. Replaced timer and still didn't work. Am embarrassed to admit all was wrong was that the timer knob was broken and spun around. But am typing this so someone else might check the knob first of all before going to all the trouble of replacing the timer. Although it was an easier job than I thought. About 15 minutes after I got the dryer pulled out. Oh well, have a new timer and knob now and got to clean out behind the washer and dryer which was needed and the dryer vent also. All is well now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CROSSVILLE, TN
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dishwasher won't start.
Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from WESTPHALIA, MI
- Parts Used:
- WD21X31899, WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Start button stuck
The replacement of the parts was simple enough, but the board appears to need a jumper which was not in the original board.
The start button works, but beeps three times and doesn’t start the washer
The start button works, but beeps three times and doesn’t start the washer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from LAWRENCEVILLE, GA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer drum wasn't spinning, but I could hear the motor and feel the heat from the heating element.
UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.
The video on the site is easy to understand and a snap to follow.
The video on the site is easy to understand and a snap to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from NANTUCKET, MA
- Parts Used:
- WR60X31522, WR02X12008, WR02X10540
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
NOISY
I FOLLOWED YOUR VIDEO............WAS EASY. THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PITTSBURGH, PA
- Parts Used:
- WR60X31522, WR02X12008, WR02X10540, WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Noisy freezer fan
Fast and easy-great video instructions for each part ordered.
All parts perfect fit.
My refrigerator is running like new again-good for another 10 years!
All parts perfect fit.
My refrigerator is running like new again-good for another 10 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriel from WASHINGTON, DC
- Parts Used:
- WR60X31522, WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Loud screeching noise from freezer during cooling cycle
I replaced the fan motor and one of the grommets. When I took the motor out it was clear it was failing because there were metal flakes from the motor on the fan blade. I followed the instructions on the posted video. My model did not have a removable bottom tray in the freezer so that was one less thing to do. Aside from that the video was accurate. I had two minor problems during reinstallation. First, it was very difficult to get the spring clamp back on the fan blade without pushing it against the motor. Recommend you get someone to help hold the spring open while you push it on. Second, the length of wire on the replacement was not exactly the same as the original and I had to move some wires around. Recommend you take a picture of the cable layout before disassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from HADDON HGTS, NJ
- Parts Used:
- WR60X31522, WR02X20092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy evaporator fan motor
Removed old replaced with new part. Easy Peasy
Was this instruction helpful to you?
Thank you for voting!