GMR05BLHWWC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from Oak Harbor, WA
- Parts Used:
- WH02X10265, WH2X1199, WH2X1197, WH2X1193, WH02X10383
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Grind noise becoming worse
Used the repair instruction paper behind the washer control panel and used the online parts diagram. Also the online responces from other customer repairs gave me the idea to take a small pipe wrench (with a sock over the bottom of handle) and tap it with a 10 lb sledge hammer to remove the alumium hub nut. *** It is a backwards threaded nut **** I did not know I was going the wrong way until I looked at the new nut and noticed it's reverse threaded!!! After that it was just taking everything apart and putting it back the way you found it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Kittery, ME
- Parts Used:
- WH12X10498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No hot water fill
- Troubleshot fill valve first. OK
- Followed leads to temperature selector switch.
- Checked resistance and live voltage at switch.
- Determined switch had failed on "hot" side.
1. SECURED POWER
2. Removed four torx screws on top of dashboard.
3. Removed six sheet metal screws from dashboard back.
4. Removed 4 leads from bad switch (one at a time).
5. Placed leads on new switch (one at a time).
6. Removed existing switch.
7. Installed new wired switch.
8. Re-installed dashboard back and top screws.
9. Op-test sat.
- Followed leads to temperature selector switch.
- Checked resistance and live voltage at switch.
- Determined switch had failed on "hot" side.
1. SECURED POWER
2. Removed four torx screws on top of dashboard.
3. Removed six sheet metal screws from dashboard back.
4. Removed 4 leads from bad switch (one at a time).
5. Placed leads on new switch (one at a time).
6. Removed existing switch.
7. Installed new wired switch.
8. Re-installed dashboard back and top screws.
9. Op-test sat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Bel air, MD
- Parts Used:
- WH01X10302
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Washer drum would not spin, broken belt
I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WILLOW STREET, PA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
would not empty the water
read about the problem ordered the part and then installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Lincoln, CA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Soap dispenser latch broke - never worked right
This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from MAYFIELD, UT
- Parts Used:
- WD12X10271, WD12X10401, WD03X10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cover, Interlock Heats Ups And Bends Causing Switch Problems
Ordered your new and improved interlock cover made with better plastic (thank you). Your new spring is also better. It's bigger and longer and is now the right size. (Thank you). Your parts are better than oem. The interlock is easy to get to. The oem one is black and you can see that it is bulged. The replacement one is gray speckled with white and black. You can see the improvement by just making a comparison. Just unclip the old one and clip in the new one. . Repace panel cover. Now it works and should work now for many a year. Thanks! Parts select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from Hagaman, NY
- Parts Used:
- WH01X10302
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
belt fits too tightly toget on easily
took two people to get this belt on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from LUBBOCK, TX
- Parts Used:
- WH13X23974
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Leaking water
Unplug electricity, unscrew 3 bolts with nutdriver from rear of top panel, expose triple valve, remove 2 screws from existing valve, turn water off & remove hose from triple valve, remove outlet hose attached to the valve,install new valve with 2 screws & replace outlet hose, attach hot/cold hoses, replace top part of washer with the 3 screws,plug in electricity & turn on the hot & cold water, that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Mount Vernon, TX
- Parts Used:
- WH01X10302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not agitate or spin dry
After confirming what I thought was the problem and reading other posts it was fairly easy to replace the belt. After taking the bottom cover loose to gain access to the large and small pulley I found out that the belt was very tight to get on as a previous customer had mentioned. I also used visegrips to hold the belt in place on the large pulley while guideing the belt on the small motor pulley with one hand and turning the drum pulley with the other hand. It helped that I had read the other post first. Next time will be a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DARYLD from SCHOFIELD, WI
- Parts Used:
- WH41X10096, WH16X513
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hose and clip were broken in moving
The parts were here in 3 days and the repair went very quickly .Quality item would do business again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Tempe, AZ
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water was leaking
My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My husband put it back in about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lakeport, AL
- Parts Used:
- WD08X10059
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door seal was never installed when machine was manufactured
removed two bottom screws on inside door panel and slid seal onto spline, reinstalled screws. Job done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dirk from Anamosa, IA
- Parts Used:
- WH01X10302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broken Drive Belt
Removed bottom washer plate. Placed belt on small, grooved pulley. Started belt on larger pulley. Clamped lock pliers to larger pulley to prevent belt from slipping off. Turned belt onto larger pulley by turning and pressing the belt close to the smaller pulley. Adjusted belt and replaced bottom plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Covington, PA
- Parts Used:
- WH1X2727
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise upon aggitation
replaced Tub dampeners Straps.
Was this instruction helpful to you?
Thank you for voting!