GSRC3KLZBFWW General Electric Dishwasher - Instructions

oversized outlet not available in local stores, this one fit perfectly

remove lower rack. place in trash. place replacement rack into dishwasher

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

Replaced the 8 year old icemaker.
Turned off power.
Did not need to turnoff water supply.
Removed the 1/4" hex head screw from the wire connector cover.
Removed the wire cover taking care to be careful with the thermister
temperature sensor which slides into a square channel in the cover.
Disconnected both wire connectors.
Unscrewed the 5/16" hex screw at bottom of icemaker to unmount the old icemaker, lift the icemaker up 1/2" and out and discard.
Installed new icemaker in reverse order.

This was the first time I took out the old filter on my new refrigerator and added the new one. It was a little hard getting the old one out because I was afraid to pull on it but it did come out ok and was easy to put the new one in.

I had to pull out the built-in dishwasher by removing the top two screws and pulling it out. I unhooked the fill tubing and drain hose. I removed the drain hose hose clamps pulled the hoses off and replaced the new part by attaching the hoses w/ clamps and pluging in the two small electrical wires and it was done. worked great! This was the only site that I was able to find MY EXACT model and the part was a perfect match!!

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Received replacement part. There is a cover over the ice box latch. Pried it off with a screwdriver head. Took the broken latch off replaced new latch to cover and replaced on the door.

Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.

Disconnected the electricity, the drain hose, and the water supply from the dishwasher. Loosened the two screws from the countertop and pulled out the dishwasher. Turned it on to it's side. Saw the damaged inlet sump. Had to remove the Pump connector to get to the inlet sump. Checked it also and discovered that it was starting to develop a small crack from the inside. I decided to replace it as well. The job involves removing the hose clamps and removing the spray mechanizm from the interior of the dishwasher to spin out the inlet sump. Not a difficult job.

unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

I asked two strong male neighbors to do the work and told them how to do it. Follow the simple directions on the box. You can Google it, but it will tell you the same directions.

Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.

The glass fits easily under a plastic ridge that is the frame holding the 2 vegetable drawers below. Slide the back side of the glass under the ridge, and then gently place the front of the glass in the groove where it goes on top of the vegetable drawers.
Its Super simple, and takes literally 30 seconds to complete.

Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!