GDF530PGM4BB General Electric Dishwasher - Instructions

1. Shut off circuit breaker power
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door

Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.

Quite simple. Only disassembly/reassembly was the spray mechanism attached to the bottom of the Upper Rack. Snaps off old and on to new rack with no tools. On this dishwasher model, there is no hose assembly running to water port, but the spray assembly is instead a integrated tube with a male port that "plugs" into a female port on back of unit. Definitely get 2 end caps.
Only difference from original, is the design of the bottom rack. To fit such that the door closes, the silverware rack is at the back of the unit versus the front. Somewhat inconvenient. Can put silverware rack in front, but then less efficient for dishes.

the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.

the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
PS12743260Manufacturer Part Number WD28X26099

Removed lower rack, slid in new Rack.

I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy

Part was incorrect Compare that to GE site saying number on both ports to different parts try to return was half the course of what I paid ridiculous So apparently I'm stuck with it Check GE site you'll see the port is different from what your sound but the numbers are exactly the same No clips to support the utensil tray

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+

Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.

Super easy repair. Took off the spinning arm, removed the Diverter Assembly (no tools required), and reassembled.

Replaced old rack.

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!

The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.