GDF530PGM3BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dawn from JAMESTOWN, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door did not latch, therefore would not operate
Replaced latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WG from VALLEY SPGS, CA
- Parts Used:
- WD26X23258
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dead spot in motor
Not having to screw with the hose clamps is the advantage here!
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from FAIRVIEW, OK
- Parts Used:
- WD21X23498
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishes not drying and no heat other than hot tap water
Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Takashi from RIVERSIDE, CA
- Parts Used:
- WD28X34744, WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper and lower racks rusted in less than 2 years.
Ordered the Upper and Lower rack assemblies. Lower rack slid right in as the wheels came with it. Upper rack had to be removed from rails and old spray arm removed so it could be used with new rack (spray arm does not come with it). Whole process took about 10 minutes, no tools needed other than your hands. Overall, installation was no hassle but sad that the racks don't last over 2 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from NAPLES, FL
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hooksett, NH
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish rack prongs rusted and broke off
It wasnt exactly the right lower dish rack to hold silverware holder. Instead of the trouble of sending it back we will use it. Silverware holder takes up some of the space for other dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from WINONA, MN
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old rack had rusted and broken tines
1. Take a picture of the old rack in the dishwasher! Just in case!
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.
Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.
Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SEBRING, FL
- Parts Used:
- WD22X33498, WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from N HOLLYWOOD, CA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
old nasty gasket needed to be replaced
youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OMAHA, NE
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack rusted out
Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!