GSD3300K70BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from EDEN PRAIRIE, MN
- Parts Used:
- WD28X31819
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rear 1/2" wheels on new rack were too narrow causing rack to fall off tracks
Removed 3/4" rear wheels from old damaged rack and installed them on new rack. Works fine now. For the price paid for this replacement rack, wide wheels should be included as part of the replacement package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
Lower Dishwasher rack was starting to rust
The rack for my model has been discontinued so they shipped me the replacement version. The wheels on the new one are skinnier than the original model so I had to remove them and replace them with the wheels from the old rack for it to fit/roll correctly. The new wheels were a little tricky to get off as I had to use a screw driver and basically manipulate/pry apart the clamps that hold them on. The old wheels just snap on.
Was this instruction helpful to you?
Thank you for voting!
Leaking shaft seal
There was no mention of a very slight rub of silicone for lubrication. I have always utilized this on all "O" rings with good results!
Was this instruction helpful to you?
Thank you for voting!
Leak at bottom of dishwasher on drain valve
Small rubber gasket needed to be replaced. Not the best design by GE, but it has lasted 11 years before leaking.
Needed to remove the solenoid to access the shaft of the valve. Tough to push gasket into place, but eventually it fit in.
Needed to remove the solenoid to access the shaft of the valve. Tough to push gasket into place, but eventually it fit in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martie from FULTON, MO
- Parts Used:
- WD12X10284
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Threads on the cap broken
A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from OLD TOWN, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher
Replace both micro switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Broggie from Burlington, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill Cap Just Keep Turning, Not Locking In Place
I Just Open Door And Put Fill Cap In And Turn That It
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from DETROIT, MI
- Parts Used:
- WD28X265
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace dishwasher basket
Pulled out old basket with holes at bottom and replaced it with new basket. Perfect fit!
Was this instruction helpful to you?
Thank you for voting!
dislodged & deformed baffle leaked after 29 years of use
I lifted out the old baffles, cleaned the soap scum from the recesses, and placed the new baffles in by hand. No tools were required, and total repair time was less than 8 minutes. the total cost was a fraction of the cost of a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from WOODBURY, MN
- Parts Used:
- WD28X31819, WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The covering over the original dishracks had worn away and the framework beneath was rusting.
The only trick was the endcaps, which were not intuitive. I followed the instructions in the following Youtube video , which direct the user to bend a tab at the rear of the endcap back away from the front using a quarter in order to allow the endcap to rotate out of position inwards into the interior of the dishwasher. The old racks then slid easily out of the dishwasher, the new ones equally easily slid in, and then the endcaps required the tab to be bent back to allow them to rotate back into position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanna from SEWELL, NJ
- Parts Used:
- WD28X265
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old silverware basket had slots that were broken and knives would fall through and get stuck.
Opened the box the new silverware basket came in and replaced the broken one.m
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leaking
I simply lifted the baffles out and cleaned the base and installed the new baffles and started the dishwasher and NO LEAKS.
Was this instruction helpful to you?
Thank you for voting!