GSD3300K65WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Vineland, NJ
- Parts Used:
- WD18X214
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water was leaking from under the dishwasher
I turned off the water supply to the dishwasher. Then took off the front panels and disconnected the water. I then unscrewed the dishwasher from the countertop, pulled it out luckily there was plenty of play in the wire, and drain hose. I turned it on its side and had to remove a couple clamps to free th piece that I was replacing. Once I got to it, it just unscrewed. I put the new one on and everything back together. It was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Henderson, NV
- Parts Used:
- WD8X181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking
Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!
Was this instruction helpful to you?
Thank you for voting!
Water leak around the Drain Valve Shaft.
Ordered the Drain Valve Shaft Seal and Push On Nut to make repair. Removed dishwasher from counter. Removed motor/pump assembly from dishwasher. Removed drain celenoid from pump. Removed old push on nut and old drain valve seal. Installed new seal and push nut. Replaced everything in reverse order. Amazingly no water leaks after reinstallation. Seams to be working fine so far....fingers crossed. Hoping to get a few more years out of this dishwasher.
Thank You PartSelect.
Thank You PartSelect.
Was this instruction helpful to you?
Thank you for voting!
The Drain shaft seal was leaking.
The solenoid and linkage was easy to disasemble, but getting the retainer (push on nut) off was difficult without removing the motor and pump. Once removed it was a snap. Getting the pump/motor back onto the pipes was near impossible from underneath. I had to remove the dishwasher from under the countertop to get it back correctly. I would reccomend doing this for this repair, as it made life a lot easier. Unwiring and removing the water supply line was not a problem either. WORKS AS GOOD AS NEW!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Lebanon, OR
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
First silverware basket had a hole in it.
Took out old one and put in the new one. Not hard at all. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nick from plainfield, IL
- Parts Used:
- WD18X214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Simple fix
This is a very simple fix. The majority of work comes from getting the unit out of it's enclosed space so it can be worked on. Once the dishwasher is out in the open, lay it on it's side, and simply unscrew some metal clamps, pop out the bad part, replace it with the new, reattach the pieces and clamps, and start putting the unit back in place.
I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.
I'll be back to this site in the future if/when other parts on other appliances go bad.
I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.
I'll be back to this site in the future if/when other parts on other appliances go bad.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
door seal leaked,and the baffles
removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from st augustine, FL
- Parts Used:
- WD09X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced timer knob
lol it just slip on in 2 seconds...but i like to thank you for your prompt service and very informative site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James W from Huntley, IL
- Parts Used:
- WD09X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Timer Knob
There is nothing worse than having a knob break off when using the dishwasher. The great thing is that I was able to go on the internet and found your supply outfit. I ordered the replacement and had it to install in less than 48 hours. The knob was the right one and now I use the dishwasher again TNX
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Rockville, MO
- Parts Used:
- WD24X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Couldn't drain water
I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Broggie from Burlington, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill Cap Just Keep Turning, Not Locking In Place
I Just Open Door And Put Fill Cap In And Turn That It
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from WOODBURY, MN
- Parts Used:
- WD28X31819, WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The covering over the original dishracks had worn away and the framework beneath was rusting.
The only trick was the endcaps, which were not intuitive. I followed the instructions in the following Youtube video , which direct the user to bend a tab at the rear of the endcap back away from the front using a quarter in order to allow the endcap to rotate out of position inwards into the interior of the dishwasher. The old racks then slid easily out of the dishwasher, the new ones equally easily slid in, and then the endcaps required the tab to be bent back to allow them to rotate back into position.
Was this instruction helpful to you?
Thank you for voting!