GSD2100V65CC General Electric Dishwasher - Instructions

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

Simply screwed in new cap

Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Put on a new cap.

Took old rack out put new rack

I would like to start-off by saying that I love this site . I've never been even remotely dissatisfied with parts I've ordered and the installation videos are awesome! I would recommend this site to anyone looking to repair appliances. Secondly, I am a retired mechanical designer with over 35 years of experience. I have a broad range of design experience in consumer, governmental, industrial and military part and product design. My opinion about the design having to do directly with my appliance is not very high and after talking with another local parts supplier discovered that this particular design is approximately 20 years old. I wonder how many dishwashers are leaking without the consumer realizing they have this problem. I followed the installation instructions provided by this site verbatim and the dishwasher still leaked like a sieve. This in my opinion goes back to my remarks concerning the design. This is a weak design at best and could benefit from an improvement in that area. After I installed the new parts, the push on nut (upon being seated onto the shaft for the drain valve flapper) was loose and spun freely. The push on nut did not properly compress the seal onto and around the flapper shaft nor into the valve housing. Water leaked through the seal as a result. I disassembled all of the parts again and placed a flat washer between the push on nut and the seal, to help compress the seal onto the flapper shaft and into the valve housing. The washer was a stainless steel flat washer with an ID that fit onto the shaft closely, but was a smaller OD than the seal. The washer was about 1/32" thick. Upon reassembly and observation, the dishwasher leak was stopped with the addition of the flat washer and my issue was resolved.

I took out the old one and put the new one in.

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.

The part came in as ordered. After removing the dish rack, I loosened three 1/4" screws (two on the strainer basket and one at the base of the spray arm. I had to slide the rubber hose down and back to disconnect the base which I did by turning counter clockwise. The new one went in by reversing what I just described. Other than two of the screws being difficult to reach, everything worked fine.Thanks for your site.

I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.

The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.

Unscrewed old one and installed the new one.