GDF530PGM5WW General Electric Dishwasher - Instructions

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Simply put it on and twist it to lock in place. Took all of 3 seconds

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Took it out of the box and set rollers on track
rolled in place ALL DONE

After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Release DW from cabinet and pull out, Unplug power.
Remove kick plate and unplug door cable.
Open door about 6 inches and using socket back out 2 bolts at bottom of door corners.
Pull door up off hinges about 4 inches and slide old gasket out and install new gasket in place.
Reset door on hinges and reinstall bolts.
Plug door cable in and reattach kick plate and plug power cable in.
Push DW back in place and attach to cabinet and adjust kick plate

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.

Got the seal, read the reviews to see how to do it, Take out the two bottom screws ,easy enough. pull the door up ,pull out seal replace new one. Easy enough, but know one said don't pull the door up too high , I did, could not get it back down to save my soul. Needles to say had to buy a new dishwasher. that sucked have the new seal gasket if anybody needs one

The upper rack required removal and reinstallation of the end caps and spray arm. Not a problem, just went on YouTube and watched the videos. The lower rack was just a matter of removing the old and installing the new. Yes, the utensil basket can not be replaced in the front, it has to be placed in the bottom rack. I installed mine on the right hand side. Maybe it isn't the best option (thanks GE), but it is better than rust on the dishes.

Popped the old one off. Popped the new one on. Easy as that.

I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.