GSD3300K70WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kim from DETROIT, MI
- Parts Used:
- WD28X265
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace dishwasher basket
Pulled out old basket with holes at bottom and replaced it with new basket. Perfect fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from PLANO, TX
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Racked rusted out
Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.
Was this instruction helpful to you?
Thank you for voting!
dislodged & deformed baffle leaked after 29 years of use
I lifted out the old baffles, cleaned the soap scum from the recesses, and placed the new baffles in by hand. No tools were required, and total repair time was less than 8 minutes. the total cost was a fraction of the cost of a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leaking
I simply lifted the baffles out and cleaned the base and installed the new baffles and started the dishwasher and NO LEAKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from JONESBOROUGH, TN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
NEEDED TO REPLACE LOWER RACK IN DISHWASHER TO SELL HOUSE
TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from WOODBURY, MN
- Parts Used:
- WD28X31819, WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The covering over the original dishracks had worn away and the framework beneath was rusting.
The only trick was the endcaps, which were not intuitive. I followed the instructions in the following Youtube video , which direct the user to bend a tab at the rear of the endcap back away from the front using a quarter in order to allow the endcap to rotate out of position inwards into the interior of the dishwasher. The old racks then slid easily out of the dishwasher, the new ones equally easily slid in, and then the endcaps required the tab to be bent back to allow them to rotate back into position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanna from SEWELL, NJ
- Parts Used:
- WD28X265
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old silverware basket had slots that were broken and knives would fall through and get stuck.
Opened the box the new silverware basket came in and replaced the broken one.m
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryll from Newville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Was this instruction helpful to you?
Thank you for voting!
Leak at bottom of dishwasher on drain valve
Small rubber gasket needed to be replaced. Not the best design by GE, but it has lasted 11 years before leaking.
Needed to remove the solenoid to access the shaft of the valve. Tough to push gasket into place, but eventually it fit in.
Needed to remove the solenoid to access the shaft of the valve. Tough to push gasket into place, but eventually it fit in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Davidson, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Mount Prospect, IL
- Parts Used:
- WD12X332
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The upper try roller was broken
Unscrewed the old roller. But it was difficult to replace the roller as the rim of the roller would not fit into the slide mechanism and allow the screw to engage the hole. What I thought would be a 2 minute job turned out to be more like 20 minutes. I suspect there is a way to release the slide stop so that the top basket could be removed with its slide bar, but I did not see how to do that. I finally was able to "force" the screw into the hole
Was this instruction helpful to you?
Thank you for voting!