GDT630PGM5WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Corinna from MOUNT AIRY, MD
- Parts Used:
- WD08X21894
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Door gasket needed to be replaced
Simple answer- do not try to do this. GE makes you replace the entire door to replace this $3 part or call them and pay $100s to fix it. We decided to replace the entire dishwasher after we went through disassembly (there are no instructions on this) only to find out we could not fix without a brand new door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hooksett, NH
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish rack prongs rusted and broke off
It wasnt exactly the right lower dish rack to hold silverware holder. Instead of the trouble of sending it back we will use it. Silverware holder takes up some of the space for other dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SEBRING, FL
- Parts Used:
- WD22X33498, WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from N HOLLYWOOD, CA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
old nasty gasket needed to be replaced
youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from LAS VEGAS, NV
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower dishwasher rack was rusting out. The rubber/epoxy coating was coming off causing rack to rust out.
Removed the old lower rack and slide the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from SCHENECTADY, NY
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Door gasket at bottom of door was falling apart and leaking
1. Shut off circuit breaker power
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josef from MT CARMEL, TN
- Parts Used:
- WD08X21894, WD08X10092
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking under door
Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from CHESAPEAKE, VA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating element broke off and burned a hole in rubber tube, leaking water.
Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from MASON, OH
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty Lower Rack
Removed lower rack, slid in new Rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Praveen from Monroe Township, NJ
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
as better as it gets
the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lesa from BETHALTO, IL
- Parts Used:
- WD13X10071
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishwasher would not know door was closed
Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Fruita, CO
- Parts Used:
- WD19X25466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower dishwasher spinning arm not working
Super easy repair. Took off the spinning arm, removed the Diverter Assembly (no tools required), and reassembled.
Was this instruction helpful to you?
Thank you for voting!