CDT875P3N2D1 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Herminio from TOMS RIVER, NJ
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Door 1witch stopped working
1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from FORT COLLINS, CO
- Parts Used:
- WD08X22095, WD01X31858, WD01X31858, WD01X31858
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
leaking from somewhere around tub
the actual gasket tub seal was easy, 10 minutes. The trim tub gaskets were a pain because I had to uninstall the dishwasher (not plumbing or electrical) then pull it out from the cabinet, remove old trim and re-install. Re-leveled dishwasher, screwed into side of cabinets but it still leaks. Can't figure out where but after replacing all the trim and gaskets its very frustrating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LAS VEGAS, NV
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door latch and springs were not connected.
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from JAMESTOWN, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door did not latch, therefore would not operate
Replaced latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- louis from ROCKTON, IL
- Parts Used:
- WD28X20164
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower rack was broken/ rusted
Just snap part in position quick to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from NEW YORK, NY
- Parts Used:
- WD08X22095
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher door was leaking at bottom.
When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from TOLLAND, CT
- Parts Used:
- WD08X22095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher tub was leaking
Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Drew from ROACHDALE, IN
- Parts Used:
- WD28X34743
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bottom dishwasher rack had rusted prongs and a few had broken off.
Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cody from Denver, CO
- Parts Used:
- WD30X20110
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Guide Rail for Rack Broke
I determined the guide rail on one side had broke when the white plastic bearings fell out of their track. I decided to replace both sides at the same time, so I ordered 2. They arrived quickly and I installed them and placed the middle rack back into the dishwasher. Went together fairly easily. I took pictures before removing the guides from the rack, so I would remember how to put the new ones back one when they arrived. Very happy with this DIY repair that easily would have taken much longer and would have been way more expensive! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from OCEANSIDE, CA
- Parts Used:
- WD28X35784
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Wanted to replace original rusted top rack of dishwasher
Needed GE Technician to install. Partselect.com had to send a second replacement rack because the first one was defective. When the second on arrived, IT TOO WAS DEFECTIVE. After the Tech tried to install the second replacement, he was forced to remove a part from the original rusted rack in order to get the 2nd replacement to even stay in the rails of the machine. Tech was great, but the Partselect.com parts were unusable as sent.
Was this instruction helpful to you?
Thank you for voting!