PDP715SYN3FS General Electric Dishwasher - Instructions

1) Pull out lower basket plate holder out. Now would be a good time to check roller wheels. 2) Grasp lower spray arm base (knurled collar on base) and turn counter clockwise to release. 3) Install new spray arm and turn knurled collar on base clockwise to lock it in. 4) Reinstall lower basket plate holder.
* Done *

Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.

Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.

I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!

I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly

Simply put it on and twist it to lock in place. Took all of 3 seconds

Pretty easy repair for this model dishwasher…
1. Turn breaker for dishwasher off.
2. Remove front lower kickplate.
3. Remove small wire connector from dishwasher door to control board connector on lower right side.
4. remove one screw to remove power wiring junction box cover on lower right side.
5. Remove wire nuts securing dishwasher power wires to incoming power leads.
6. Remove 2 screws holding junction box to dishwasher frame and move out of the way of the plastic control board shroud.
7. Remove screws holding control board shroud and lower control board.
8. Disconnect 3 electrical connectors from board.
9. Remove screw holding control board to shroud.
10. Install new control board into shroud in same orientation, reinstall electrical connectors, reinstall board/shroud assembly, reinstall junction box, reconnect power wires with wire nuts and electrical tape as required, install junction box cover, reconnect door connector to board, reinstall kickplate, turn circuit breaker back on.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Replaced lower spray arm.easiest repair ever saved tons of money doing it myself

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.