GSM2200V65BB General Electric Dishwasher - Instructions

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

I read all the other repairs first to find out what I had to do. I then took front cover off the bottom of dishwasher. Identified the leak was coming from drain seal. I shut breaker off unpluged wires that were hooked to the drain valve sensor. removed the clip carfully as not to damage it. Removed srews that held down drain valve. removed the push on nut that holds drain seal in place. then removed old seal. I wiped down shaft to get ride of any corrosion and reinstalled new seal with deep socket and a srew driver. I installed new push on nut with another size socket. I fitted drain valve to shaft, used plyers to gently to pull shaft so I could put the c clip back onto grove on the shaft. reinstalled spring and plug wires back in turned breaker back on. I turned the dishwasher on and it did not leak. I was very happy that i did not have to take the dishwasher out. I did all repairs with everything still hooked up.

The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick.

To remove the upper rack guide end caps, pull the inside flange gently to the rear, then twist the cap out of the track. Then the rollers come out easily, and replacing them involves merely snapping them in place over a rack frame part. Piece of cake! Roll the rack back into the guides, and replace the end caps. No tools needed!

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

Saved a bundle over the cost of a new dishwasher. by ultimately replacing the entire motor/pump assembly with one ordered from PartSelect.com And a bonus was a much quieter operating dishwasher!!

Here's what I did:

First tried replacing leaking drain valve shaft seal.
Removed entire motor pump assembly. Replaced seal. Still leaked (although less) because drain valve shaft was worn (corroded.)

Next ordered the entire motor/pump replacement assembly. The parts arrived in 2-1/2 days. (Should have replaced entire pump assembly to start with - all of the same labor to replace just the drain valve shaft seal.)

Anyways, instructions were very clear and well illustrated. This replacement took less time than to do the drain valve shaft seal.

Very simple repair:
1) Shut off water supply, electric power
2) remove front bottom insulated dishwasher cabinet cover grills.
3) disconnect drain hose and catch water in shallow dish.
4) disconnect water supply at solenoid valve.
5)disconnect electrical inside junction box and remove cable from dishwasher.
6) remove two under counter screws to top of tub
7) slide dishwasher out from under cabinets.
8) place soft carpet to cushion left side of dishwasher to avoid potential damage to water inlet to tub..
9) lay dishwasher onto left side. (Not right side, as jet dry reservoir wiill drain empty all over floor.)
10) unfasten motor support rod, power connector, and drain solenoid power connector.
11) unfasten motor ground wire.
undo pump inlet and outlet boot clamps.
12) remove old motor/pump assembly.
13) prepare new motor/pump assembly drain hose adapter stub reducer diameter to pump drain outlet. (tighten two hose clamps provided/)
14) place new motor/pump assembly into inlet and outlet boots.
15) fasten inlet and outlet boot clamps firmly tight.
16) install new, longer motor support rod (front)
17) install motor ground wire and new, fine thread grounding screw,
18) connect motor power to new power pigtail and plug new pigtail into motor power connection,
19) install wire wrap tie threaded through the support rod to front frame hole and support motor power wires/
20) install wire wrap tie through drain valve solenoid metal support holes and loop around solenoid power wires to support them.
21) tilt dishwasher upright and slide back under counter cabinets. Guid power and water supply lines to right under side of pump motor, and drain hose to left side.
22) reattach drain hose to new motor/pump drain stub reduce adapter, tighten hose clamp.
23) support drain hose with wire wrap tie looped over frame on left side.
24) reattach water supply to inlet water solenoid valve and tighten firmly.
25) redo electrical power supply connections to dishwasher hot, neutral, and ground (120VAC).
26) check level of dishwasher tub and adjust front and rear leveling legs on left and right sides. BE SURE LEVEL, OR WATER MAY SPILL OUT TUB WATER INLET OPENING DURING OPERATION.
27) remove inside tub drain trap screen (two screws) , and pull out sump baffle. Check for and remove clear any foreign objects inside tjhe sump.
28) replace sump baffle (flat baffel towards fromt. and tub drain screen cover.
29) Turn on water supply and electirc power supply.
30) Test wash a load of dishes and check for leakage.
31) reinstall fromt lower insulated cover grills.

Wow, the new motor/pump assembly operates very quietly compared to the old one - this is a pleasant and unexpected bonus.

No problems encountered.

Total time was about 2.5 hours to do all of above.

A no brainer. Simply open dishwasher door, remove lower rack and set new rack in place. Roll the new lower rack in dishwasher and close door. It fit perfectly and life routine was instantly on it's way without disruption.

The repair only required me to lift out the old unit and set the new rack into the dishwasher. I was pleased that there was nothing to put together. The rollers were already attached.
It took longer to open the shipping box than to do the installation.

I called the repair guy, and he told me I'd have to replace the motor/pump assembly. He said he could do it for around $250 to $300. I logged onto this website for a look and saw the seal available. After reading the other responses, I figured with a seal and the cheap push-nut (that sometimes gets mangled upon removal), it would be worth a try.
I pulled the dishwasher partly out from under the cabinet; disconnected the front support mount, the drain hose, and the two water boots; dropped the motor/pump assembly; removed the solenoid; removed the e-clip, push-nut, shaft, and old seal; and then reinstalled everything. The hardest part of the repair was the tight working conditions. I wonder how many people pay hundreds of dollars because of this $15 part.

If you are replacing an overheated solenoid that had the plastic melt, don't forgot to order a armature and link as well. I made this mistake and had to wait another week to fix the dishwasher. The repair wasn't too bad. The most time consuming part was putting the E-clip retainer ring back on the diverter shaft. Tipping the dishwasher back some really helped for me to have more room to see and work with.

The shaft pulled out of the housing when I tried to get the push nut off. I had to take the pump housing out in order to get the shaft lined up with the valve when reassembling. In the end, the shaft had so much slop that no seal could keep it from leaking. Time for a new dishwasher.

I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.