PDW7380N15SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from SEDONA, AZ
- Parts Used:
- WD01X10176, WD01X10175
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher would only 'partially' drain; dishes needed more rinsing.
Called repairman: announced that the drain pump was gone. Did not seem right. Went to the website. Found what I was looking for. 49% of the time it was a check-valve issue; only 26% of the time was the pump the problem. Took the unit from under the counter; got it on its side; removed the drain pump. Found my first check-valve, but thediagram showed a second lower one toward the sump. Having located both and purchased two valves and and the lower holder piece, I was ready to finish the job. Quarter-inch nut driver and a screw driver and the valves were in and the drain pump re-installed. Most difficult in my case was getting the dw back into its spot and lashed down! Thanks for the good guidance!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from NAPLES, FL
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cincinnati, OH
- Parts Used:
- WD35X21038, WD12X10206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack roller and JetDry cap were missing
Opened the package, opened the plastic parts bag, installed the roller and the cap.
Whew!
Whew!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Jacksonville, FL
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front door on Dishwasher Leaking
Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessie from TYLER, TX
- Parts Used:
- WD12X10206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Jet dry rinse cape destroyed.
Got the part the next day.. opened it and just screwed into place!
Easy as could be. Thank you!!
Easy as could be. Thank you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BURKBURNETT, TX
- Parts Used:
- WD12X10206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rinse aid cap leaking
Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ANNAPOLIS, MD
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Leaking Solenoid valve
1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonni from VACAVILLE, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
leg fell off of bottom rack.
Slid it in. Very easy and the replacement part is built better than the original part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from PALMER, MA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers and axles were worn out
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John C from SPRINGFIELD, VA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom dishwasher rack rusted out
Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from PEORIA, IL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack was rusted and broken.
It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from CHEYENNE, WY
- Parts Used:
- WD12X10109, WD12X10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old parts showing wear
Watched a YouTube video on disassembly, parts replacement, and reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!