GSD3830Z07WW General Electric Dishwasher - Instructions

I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

Simply opened the dishwasher door, removed the gasket insert located in the middle inside of the door and replaced with new. Also went ahead and replaced the seal on the inner edge of the inside dishwasher door. Found very simple instructions on Google on how to do make this repair. Very easy!

Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...

I removed 2 screws a wire plug connector and replaced the old part. The total repair including putting the cover plate back on only took about 15 minutes. Also I saved approximately $130.00 by doing this repair my self.

At first I thought I would call a repair man.Then I thought-that will be at least $100!So we went online and found the part.Took about four days to arrive.I pulled the dishwasher out and turned it on it's front.The little leaking hose was easy to remove,two clamps,and the new one installed.Total cost-$14.00.

Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.

First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.

Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.

from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Your site is great! Saved me a service call for a repairman to come out and tell me what was wrong, order parts and then come back. Total repair was less than $90 including parts and shipping. It arrived in two days from when I ordered it. I ordered the replacement door gasket, the gasket insert and a new checkvalve. This was a super easy fix and I am a girl too boot! I am proud of myself!

I used a phillips screwdriver to take off about 8 screws off the white inner door fascia in order to replace the door seal. Keep this panel upright and do not lay it down since the rinse agent will leak out all over! Found out that the hard way.

Removed the old, dried out, outer door gasket, centered the notch that was on the new gasket at the top of the door and installed it all the way around in the door gasket groove. Installed the gasket insert at the bottom where the door gasket comes together on the bottom of the door.

After that was completed I used a 1/4" nutdriver to remove the 4 hex screws at the back of the dishwasher for the cover that is over the check valve. It is white and has a very fine mesh screen.. so easy to identify.

The old check valve was filled with crud and and the rubber was deteriorated. I just backed the old one out counterclockwise and put in the new one, a little better than finger tight. Replaced the cover and the hex screws with the 1/4" nutdriver.

Reinstalled the white inner door panel, insure the door handle comes through the hole in the front prior to attaching your screws back in place. Closed the dishwasher. Ran it on rinse/hold cycle to make sure no leaks before going for a full wash. Works great and drains now too.

Your site is a lifesaver! Thanks!!!

Loosened the clamps connecting the pump, disconnected all electric and stabilizer arm. Simply unscrewed the solenoid bracket and replaced with new part.

Removed the 4 screws holding the filter screen assembly in the back of the tub. This exposed the Piston and Nut assembly which unscrewed fairly easily.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.

First i removed the front cover from the dishwasher then i reached under dishwasher and removed the hose ,then installed the new one. the hose was different size on each end. it took a factory hose to fit it. The diagram that partsselect showed of the dishwasher (the breakdown) made ordering the right part a breeze. Thanks PartSelect.