GDWT358V50SE General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Doon, IA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cap was melted
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Boise, ID
- Parts Used:
- WD18X10026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Sump was leaking from previous repair person
Removed Dishwasher, inverted it and replaced the sump housing. There are 2 screws mounting the top of the dishwasher to the counter, a water connection and the electrical connection. Remember to turn the water off and the electricity off. Slide the DW out on carpet. Carried it to the garage to affect the repair. Reinstalled the dishwasher. Most difficult part of this is that the water hose is really short. I used a 6ft extension so that the next time I have to pull this out it will be easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MONICA from ENCINITAS, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The bottom rack had broken wheels and rusted prongs
Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J from Walnut, CA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Leaking water when in use.
Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Ramsey, NJ
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower Rack would no longer roll out. Had to lift out lower rack.
Once we ordered both the "Stud Roller" and "Roller Lower Rack" the repair was simple.
The previous studs mostly disitegrated, so their removal was not an issue. The wheels pulled off easily.
I recomend getting new studs and rollers for all of the wheels on your rack. For me, that was 8 wheels and 8 studs.
First, take the rack out and flp it upside down in a convenient working space. Next, remove all of the old wheels and studs from the rack and discard. Then, snap the new wheels on to the new studs. Next, atached the stud (with the wheel) to each of the 8 spots on the rack. Put the rack back in the dishwasher and walla!
I can't beive that I waited almost two years to make this simple repair.
The previous studs mostly disitegrated, so their removal was not an issue. The wheels pulled off easily.
I recomend getting new studs and rollers for all of the wheels on your rack. For me, that was 8 wheels and 8 studs.
First, take the rack out and flp it upside down in a convenient working space. Next, remove all of the old wheels and studs from the rack and discard. Then, snap the new wheels on to the new studs. Next, atached the stud (with the wheel) to each of the 8 spots on the rack. Put the rack back in the dishwasher and walla!
I can't beive that I waited almost two years to make this simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from PHOENIX, AZ
- Parts Used:
- WD28X10128
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
OLD ONE HAD HOLES IN IT AND SILVERWARE WAS SLIPPING THRUGH THE BASKET TO THE INTERIOR OF THE DISHWASHER
1. remove old basket. 2 Place new basket.. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Cedar Rapids, IA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Silverware Basket Broken
Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Hendersonville, TN
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rollers on my dishwaher kept falling off and the lower rack wouldn't roll in or out.
We removed the remaining rollers, inserted the studs into the rollers and attached to the lower rack. Easy. I can't believe we put up with this for so long. We appreciate your quick service. So much easier than going shopping and waiting for the parts to come in and then having to go pick them up. Thanks for being there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Grand Isle, VT
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking.
Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.
Then reversed these steps and I was done.
Then reversed these steps and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DARYL from RENTON, WA
- Parts Used:
- WD08X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Had damage to the door seal from items sticking up in the silverware basked rollin past it.
No tools required. The seal just pushes into a channel around the tub. The lower ends are held by a wire that spans the lower edge of the door. I started with the lower end since I didn't know just how the seal was installed and found the wire that sticks into the hollow center of the end of the seal. The seal just pulls out so removed it and the wire. Cleaned the seal channel and wire and installed the new seal starting at the bottom and working upwards. after the lower ends are anchored,I found the center of the seal and upper channel and pushed it in place and worked around the corners and down. I did that because I have seen seals stretch as you push them in place and end up in the middle with excess material you have to work back into the seal channel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Nashville, TN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch to pop up door to soap dispenser broken.
I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Silver Spring, MD
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels kept falling off the dishwasher rack
This is one of those things that after you do it, you wonder why you didn't do it sooner. Installation was a snap - literally. All I did was remove the wheels from the bottom dishwasher drawer (they didn't stay on anyway...and one had fallen off mid-wash and melted). I was able to re-use the wheels and simply snap in the new axels - which have a far superior design. I ordered a couple extra wheels to replace the one that melted and to have on hand...just in case. Delivery was incredibly fast - I received the parts the day after I placed the order. Why didn't I do it sooner?!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lady Lake, FL
- Parts Used:
- WD15X10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water Leaking
First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Stamford, CT
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
White latch on soap dispenser broken- would not latch
The first posted instruction is dead on (except there are 14 phillips screws (not 10) on inside of door. Also, when reconnecting the 2" quick connect, make sure it is fully inserted - otherwise the numbers on the display panel will not show correctly. Mine didn't the first time, and I had to re-open the door panel and giggle around with the connection to get the numbers to display properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from NEW RINGGOLD, PA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
faulty valve
Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order
Was this instruction helpful to you?
Thank you for voting!