GDT545PSJ6SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from CASTLE ROCK, CO
- Parts Used:
- WD01X10569
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The pulley cable had broken
Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from SAN JOSE, CA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dispenser no longer opened during wash cycle
Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LAS VEGAS, NV
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door latch and springs were not connected.
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Saint Joseph, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water in dishwasher
It took longer to uninstall and reinstall the dishwasher than it did to change out the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaRay from PRESCOTT, AZ
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
soap did not dispense correctly
Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from YUKON, OK
- Parts Used:
- WD01X10569
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
REPLACE DOOR CABLE
Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from FAIRVIEW, OK
- Parts Used:
- WD21X23498
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishes not drying and no heat other than hot tap water
Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivan from MANSFIELD, TX
- Parts Used:
- WD19X25187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Not Draining
The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from FORT SMITH, AR
- Parts Used:
- WD21X31910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not turn on.
Watched YouTube video on how to diagnose problems. Once part was identified ordered from Partselect.com and replaced the user interface circuit board. Dishwasher is now working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from South Charleston, WV
- Parts Used:
- WD08X21894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
seals were leaking (they'd been chewed on by a mouse)
the hardest part was removing the door from the face of the washer. Getting the door off required accessing the sides, so I had to lower the feet so it would slide out of the recess it sits in.
Disconnecting the springs for the door was straight forward and simple. once those were disconnected, it lifted off the hinges easily. The seals themselves were simply press-fit into the recesses. the old ones pulled loose cleanly and easily.. the new ones pressed into place very simply and without any real effort.
Getting the door back on was a little problematic, mostly in getting the hinge pins to line up properly.. but once it settled in, it line up itself, and the springs were easily replaced. I re-leveled the dishwasher, and then ran it for a full cycle to ensure it wouldn't leak anymore.
Disconnecting the springs for the door was straight forward and simple. once those were disconnected, it lifted off the hinges easily. The seals themselves were simply press-fit into the recesses. the old ones pulled loose cleanly and easily.. the new ones pressed into place very simply and without any real effort.
Getting the door back on was a little problematic, mostly in getting the hinge pins to line up properly.. but once it settled in, it line up itself, and the springs were easily replaced. I re-leveled the dishwasher, and then ran it for a full cycle to ensure it wouldn't leak anymore.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from TOPEKA, KS
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old tray was rusting.
Simply pulled the new one out of the box and put it into the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter A from HOLLAND, MI
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber Coating worn off rack...causing Plates to get rusty on their edges.
Open box...remove old rack from dishwasher...roll in NEW rack. Done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Welsh, LA
- Parts Used:
- WD28X35779, WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged upper and lower rack assembly
Upper rack I had to reuse the old power was assembly but it just snaps into place. Lower rack literally just place on roller track and it was done. No tools required. Extremely satisfied with my purchase. 10/10 recommend!!
Was this instruction helpful to you?
Thank you for voting!