GDT535PGJ6WW General Electric Dishwasher - Instructions

I removed the old gasket and installed the new one in the same position as the one I removed. I had to feel with my fingers for the ridge to insert the gasket so that it would hold. I must admit that I was skeptical that it would work (the old one didn't even seem very damaged). I ran a cycle and there was no more leaking. We've been using the dishwasher ever since with no issues of leakage.

Very satisfied customer.

Replaced heating element. This was the path of least resistance but the problem persisted. I tried resetting the dishwasher but still nothing. My last resort is the circuit board. I checked the relays on the old board and they are fine so it must be something else on the circuit board. The dishwasher is not really that old (4 years) and everything else is fine. Just ordered the board so I really hope this fixes the problem.

Online instructions said to remove door. Found no need to. Only need to release one hinge by sliding door upward after removing 2 screws at bottom edge of door which releases both hinges. With door lifted just pry out old seal (it will be stuck so use a strong screwdriver). Then slide new seal in place. Lower door back down on hinge. Job done.

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

The dishwasher had been installed before we added 3/4 oak floor, so I could not pull the dishwasher out from under the counter. That will be a major project when the dishwasher dies.
To remove the door, I removed the two 1/4 " screws on the right and left bottom of the door. I used a box wrench since that was the only way to reach them. One had corroded due to a leak. it took some coaxing but finally came loose. The hint about opening the door 27 degrees and propping it open with two Allan wrenches through the hinge holes was very helpful. Then I lifted the door a little and gently pushed toward the counter releasing the door form the hinges. I took the door off to find a leak and found the right corner edge of the inside tub had cracked. Not sure how this happened. I cleaned and sanded the crack area and used J-B Weld to epoxy the crack. Replacing the gasket was easy. Slide out the old, slide in the new. Everything went back together smoothly. If I hadn't needed to repair the tub, the hint about opening the door all the way and sliding it out part way might have worked to change the gasket. Note. Unlike a stove door the dishwasher door is not that heavy.

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

First went to U Tube to view installation instructions and location of part. It was fairly easy to replace since I had installed the unit. I was able to move the unit out enough without disconnecting any line since there was enough slack in all three connections, only shut the power off. I did use the new parts even though the older ones were not broken. The nylon pulley wheel had built up with lint causing the cable to come off.

just bolted on the new one and hooked up the hose

Took old valve assembly off and replaced with new assenbly

The lower tray was simple. Lifted the old one out and placed the new one on the lid of dishwasher.

Upper tray: Used the closed point of scissors to gently push the little piece of plastic on the slide and removed the cap on each slider. Pulled the damaged tray off of the sliders. Removed the piece that shoots the water onto the dishes and placed it on the new tray. Put the tray back on the sliders and replaced the little caps back onto the slider so that the tray did not come off of the track. Voila!!

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.

The service lady looked up possible trouble items and narrowed it down to the flood switch. Being the most likely cause, I ordered a new one. I removed both trays, the lower sprayer, and both screens. The flood switch has an electric plug on the bottom of it that just pulls off. Just as with other appliance repairs, I actually got the old flood switch to work again before trying the new one. I should have tried to free up the float before ordering the new one. But in case this happens again, I’ll just put the new one in.

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...