GDF520PGJ6CC General Electric Dishwasher - Instructions

Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid door back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.

Didn't actually do the compete repair but got close. Pulled out dishwasher, disconnected and checked continuity on the existing heating element (about 16 ohms) the new element was also about 16 ohms. This indicates they both were working fine and no need for replacement. Next step would have been to swap the elements would have been simple. Tried to replace main board as well, still not the issue so giving up and replacing the dishwasher. It wasn't the high temp cut off thermostat either incidentally and no error codes in maintenance mode. Check continuity of your existing element before ordering to save aggravation.

Open the washer, remove the bottom dish rack, then twist off the bottom water sprayer. Use a screwdriver to remove the mounting/ stabilizing screws so you can slide out the dishwasher. Close the dishwasher and slide it out. Underneath at the back there are two wires powering the drying element, carefully remove them. Use an adjustable wrench to remove the two plastic mounting nuts for the drying element. Open the washer and remove the old drying element, and insert the new element. Reassemble the dishwasher in the reverse order if disassembly.

1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.

1. Pull out dishwasher (not all the way) 2. Open the door. 3. Remove the white rope holding the door hinge (both sides) 4. Remove the door by pulling up when the door is open about 4-8 inches. 5. Lay the door on the floor ( put something under the door so not to scratch the front. 6. Remove the small bolt at the bottom of the door (both sides). 7. Slide the hinge back, up, then out. 8. Where the hinges were are another set of bolts, remove those (both sides) 9. Grab the top part of the door (the part with the buttons) and slide apart. 10. Remove the styrofoam carefully. 11. Disconnect the wiring harness. 12. Remove the 6 screws holding the Despenser tray in place. 13. Put in new Despenser tray and put everything back together.

repair under warranty for Home Depot. Ordered new controller, new sump manifold, new piranh clamp kit, new diverter passive main assy, installation took 6 months. Could not finish as GE had changed the diverter to a new design with the same part number that the repairman had no knowledge of and there is no part available for the same configuration of the one that went bad, after I called GE tech line they were not aware of updates. Giving me the same numbers. The new design works if you order a new conduit main. As the old one in the dishwasher will not connect to the new Diverter. New deverter no. WD19X25278 and the new main conduit is the same as the old configuration no.WD12X21681 . The repair people and parts people are not yet aware of the design change and availability of parts, as most are out of stock and no updated pictures of the new design. Repair warranty washed their hands of this and Home Depot after 6 months gave me credit of my full price I bought this for 3 yrs ago. Repairing myself and sell.

I fixed this issue by replacing the Dishwasher Tub Gasket (PS11774412) and the gasket on the bottom of the door (PS11700870). Replacing the tub gasket is very easy and straight forward. You just pull it off and put the new one on. The door gasket was much more complicated. See the steps required for replacement below:

The * indicates the part number in the diagram I am referencing

1. Remove the Toe Kick Assembly (*759)
2. Remove screws holding dishwasher to counter and pull the dishwasher out
3. With door shut, disengage the springs on both sides from the arm hinge assemblies *800 (I did this by taking the rope off the pulley hinge *734)
4. Disconnect the wire going from the dishwasher body to the door (there are two or three supports for the wire that need to be removed for it to come free)
5. Open the door about 15 degrees and pull the door upward (only one angle will work for removing the door)
6. Place the door on its front on the ground
7. Remove the two screws (*745) that hold one of the arm hinge assemblies to the door and pull the hinge away from the door (you don't need to pull it all of the way out)
8. Pull the old gasket out to the side and install the new gasket

Replaced bad roller carrier with a new one.

We bought this GE dishwasher new. After 9 months, we started noticing the dishes were not cleaning well. Eventually, the machine just filled up with water and drained. The washing arms didn't work. I replaced fill valve, but that didn't solve it. A GE Tech ran a diagnostic and informed us the pump motor was bad. It was off warranty and repairs would be $300. However, he noted it was easy to do on my own. Two pipe clamps. The part from PartsSelect was 40% less than ordering from GE and was a GE part. Replacement took half an hour and that includes getting it wrong once (one connection leaked due to a bad job attaching the pipe clamp). Works like a champ now.

just bolted on the new one and hooked up the hose

Took old valve assembly off and replaced with new assenbly

Repair went fine, getting the right pump was the problem. I started with my local appliance parts house, they ordered part came in 3 days. Upon picking it up I noticed that the pump was shaped slightly different and the electrical hook up was totally different. Asking the parts guy what happened he said they must have sent the wrong pump. Returned it for credit and ordered it again. Four days later the same exact thing occurs. Parts guy credits my account and says better go directly to GE. Wait 10 days for GE, for this part and once again same odd looking pump with wrong electrical plug. My son who is a welder by trade asks me if there is a packet of parts in carton and yes there is. He says that perhaps there is a converter for the electrical. That was the solution no one told us that pump was universal and needed the adapter. Not even the 2 different tecks at first house. Perhaps that should be stated in the part would have saved us tons of time. Thanks D

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

Removed toe kick. Removed door counter weights and placed door on soft surface. Removed two bolts(I was able to leave hinges in place) slid door panel down and off. Removed plastic snap fit cover and 4 bolts from UI board. Two of the stand-offs where broken, glued them back into place. Ensured jumpers were set to my model, snapped cover back in place and remounted door. The dishwasher now runs through the cycle and clean light but did not dry. That turned out to be a bad flood switch.

I got lucky and found the diagnostic test instructions tucked inside the washer under the kick plate. From there I ran the tests on each component until I narrowed it down to the pump. The pump cost me less than local dealers. The install went well. Watched the online videos to make sure I was doing it right. Was actually very easy and saved hundreds over a service call.