GDF520PGJ6BB General Electric Dishwasher - Instructions

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!

The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.

The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.

One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.

I replaced the User Control and Display Board and it is working very well now. The important things that should be noted are to take off the door and to open the door cover by unscrewing it. Those screws are located at the bottom of the door and two are hided inside.

Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

2 hose clamps, connect the wire with the wire adaptor suppled

I followed the U tube instructions already put out part select.

YouTube search indicated the common problem was the Dishwasher Electronic Control Board, part # WD21X10537. YouTube was wrong. $83.76 mistake. (not Parts Selects fault)
I continued my search and stumbled on JustAnswers.com for $38.00.
They diagnosed the issue by me describing the lights that were blinking and for how long, and quickly told me the door latch is not registering. However, said it is rarely the door latch, but rather the Electronic Control Board, part # PS12726419 for $105.90. What the heck, I'll bite.
Bought both parts at Parts Select, quick shipping, solid packaging and good return policy (learned from previous experience). I did not return the 1st part, figured it probably wasn't long for this world anyway.
Dishwasher is running fine again. The combination of JustAnswers.com and PartSelect.com is far better than an extended warranty. Extended warranties last 3 yrs in most cases and cost as much as I spent. Someone with smaller hands could have done both repairs much quicker.

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

Simple answer- do not try to do this. GE makes you replace the entire door to replace this $3 part or call them and pay $100s to fix it. We decided to replace the entire dishwasher after we went through disassembly (there are no instructions on this) only to find out we could not fix without a brand new door.

Board did not work. The socket for the jumper pins wasn’t installed on the board. Not sure if it was the correct unit. Decided to forget about doing a repair and just replaced the unit

1. Take a picture of the old rack in the dishwasher! Just in case!
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.

Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.