GDF510PSJ6SS General Electric Dishwasher - Instructions

-Disabled power.
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.

I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.

I would read this project very easy for somebody with technical skills and easy with no prior skills

Got the seal, read the reviews to see how to do it, Take out the two bottom screws ,easy enough. pull the door up ,pull out seal replace new one. Easy enough, but know one said don't pull the door up too high , I did, could not get it back down to save my soul. Needles to say had to buy a new dishwasher. that sucked have the new seal gasket if anybody needs one

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.

In did the drain screen, undid two nuts on top, removed panel, undid plastic ring, undid two screws with but driver, pulled sensor up, dried up any water at bottom, installed new sensor and follow steps in reverse. It worked!!!

Not having to screw with the hose clamps is the advantage here!
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.

Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.

De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.

I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.

Replaced latch

Simply pulled the new one out of the box and put it into the dishwasher.

The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.

The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.

One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.