PDT775SBN0TS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jay from ABINGDON, MD
- Parts Used:
- WD15X26140, WD01X22514
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Valve was leaking
Took old valve assembly off and replaced with new assenbly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rickey from POPLAR BLUFF, MO
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm broke
Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BRUCE TWP, MI
- Parts Used:
- WD01X31858, WD01X31858, WD01X31858, WD35X10383
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Old Trim Tub Pieces were bent from an improper installation
I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from FAIRFAX, VA
- Parts Used:
- WD15X26140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher would not start Would run if you added 2 qt. water manually
Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Rio Verde, AZ
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower arm spray had hole melted in it
Simply put it on and twist it to lock in place. Took all of 3 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CROSSVILLE, TN
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dishwasher won't start.
Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CROSSVILLE, TN
- Parts Used:
- WD22X33499, WD08X22095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Water blowing out door
Replaced lower spray arm.easiest repair ever saved tons of money doing it myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BENJAMIN from ONALASKA, TX
- Parts Used:
- WD12X26146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
3 Plastic rollers on bottom of dish basket came off and melted by the heating coil in dishwasher,
Simply pick the basket up to slide wheels onto axles and push in until they lock in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CONNEAUT, OH
- Parts Used:
- WD22X20688
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hub that holds the spinner for the top water in the dishwasher broke
the design of this part is easy to break when closing the top rack.
there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher
the part broke when closing the rack [a dish too tall hit it]
it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel
there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher
the part broke when closing the rack [a dish too tall hit it]
it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PeggyAnn from EAST DUBLIN, GA
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken latch
My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Park Hill, OK
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large hole in spray arm
Popped the old one off. Popped the new one on. Easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mason from JESSIEVILLE, AR
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm locking lugs had worn and it would pop off when the dishwasher was in use. It fell on the heating element during the dry cycle and a hole was melted through it.
I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jedrino from HAWTHORNE, CA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Thumping Sound during the WashRinse cycles
Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herminio from TOMS RIVER, NJ
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Door 1witch stopped working
1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sau from NILES, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Dishwasher would have water left inside over a few days
Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight
Was this instruction helpful to you?
Thank you for voting!