CDT706P2M5S1 General Electric Dishwasher - Instructions

Not having to screw with the hose clamps is the advantage here!
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.

Pretty easy repair, since I installed the DW, so knew how it went in,
turn off breaker, shut off & disconnect water, disconnect drain line into disposal, siphoned water out of bottom collection basin below sump filter.
Slid DW out from under counter & laid on it's side.

Glad I watched a YouTube video so I knew to pry open 1 of 2 crimp style hose clamps on the old drain pump, then made sense why this was a drain pump "kit" that included 4 or 5 standard band hose clamps.

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!

Super easy repair, just removed the old latch and replaced it with the new one.

Just snap part in position quick to do.

When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.

Followed instructions sent with wash arm kit replacement. Very easy.

Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.

Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

I determined the guide rail on one side had broke when the white plastic bearings fell out of their track. I decided to replace both sides at the same time, so I ordered 2. They arrived quickly and I installed them and placed the middle rack back into the dishwasher. Went together fairly easily. I took pictures before removing the guides from the rack, so I would remember how to put the new ones back one when they arrived. Very happy with this DIY repair that easily would have taken much longer and would have been way more expensive! Thank you!

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

I followed the U tube instructions already put out part select.

Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!

Pulled washer out of space to access cables to the door. Removed moved the cables by stretching springs and unhooking cable from door. Disconnected wire from door to machine in body of machine. Opened door an lifed on an angle that allowed door to be lifted out of hinges. Unscrew and remove hinges on both sides. Remove by simply pulling them straight in direction of the bottom of the door. Then unscrew bolts on either side that are now exposed after taking hinges out. Then push inside of door up and remove. Unscrew the control board unit. Un plug cable to control board. Remove bezel cover. Then carefully unsnap unit case and remove board. Replace with the new board. However since this is a replacement part it must be configured for your machine. Instructions shou you the configuration. However where I ran into a problem was dining out how to set it. There were no switches. What I learned was that altouch it looked like one piece the jumper connections actually were four separate pieces that were tightly fitted together. In order to get the configuration you simply have to lift the jumper connector up. Once done reverse process and your done. If I did not run into that one issue repair time should be 30 minutes tops.