CDT845P3N0D1 General Electric Dishwasher - Instructions

The repair is easy for most if you have basic skills.

1. Cycle your unit to make sure all the water in the tub is emptied. (Start a cycle then cancel it which forces it to empty)

2. Turn off the power at the circuit/fuse panel & also turn off your water supply going to the unit which is usually under the sink with your sink plumbing.

3. Have a few old towels handy, there will be a little water but nothing that requires a wet shop vac, etc.

4. Remove the bottom kickplate (should be a screw on each side of the front of unit)

5. Disconnect the power supply wiring to make removal easier.

6. Disconnect the water supply line (have a towel handy there will be a little water in the supply line)

7. Unscrew the mounts either at the top and/or sides of the washer depending on the install method into your cabinetry.

8. Carefully slide out the unit.

9. Carefully turn the unit on its side or upside down depending on your preference to work on the underside where the pump is located. Again have a towel or two handy there will be some water that leaks out from the tub even after forcing an empty cycle.

10. The circulation pump is easy to remove. First plug the power line, there is a clip to disengage to separate the plug. A small flat screwdriver will help.

11. If this is a first time being replaced it will probably have crimp style hose clamps on the two lines coming off the pump. Again a small screwdriver will help pry it apart. Throw these away your pump kit will have new hose clamps for installation.

12. Once these clamps are removed you can slip the hoses off and the pump will be free to remove from the unit.

13. Installation is easy. Make sure the rubber hoses seal completely around the unit before clamping. Pay attention to make sure its sealed evenly, your unit will leak water otherwise once its functioning again.

14. My recommendation is to reassemble, slide the unit back into your cabinetry and hook your power and water supply up. Before you screw the unit back into place and close up the bottom panel, start a quick cycle. Within that first minute when the unit is filling and starting the circulation pump you can watch underneath and make sure your circulation pump lines are sealed and not leaking. Once satisfied, you can then stop the unit and finish securing the unit with mounting screws and closing up the bottom kickplate panel.

Good luck! You can do this :)

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

Just snap part in position quick to do.

When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.

Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,

the actual gasket tub seal was easy, 10 minutes. The trim tub gaskets were a pain because I had to uninstall the dishwasher (not plumbing or electrical) then pull it out from the cabinet, remove old trim and re-install. Re-leveled dishwasher, screwed into side of cabinets but it still leaks. Can't figure out where but after replacing all the trim and gaskets its very frustrating.

I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly

I had to replace a docking port. Parts Select had the part, labeled as stainless, just as this survey indicates. Well folks, the part I received is 100% plastic. It it the correct part, just not stainless. Should it have been stainless due to a faulty plastic design? I don’t know.

I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.

Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.

Performed all checks on youtube...water coming in, course and fine filter cleaned, drain pump working (heard it come on and no water present and cycle end). Swapped water inlet valve bc it was the cheapest poss fix $19. No luck. Ordered circulation pump and motherboard. Swapped pump, very easy with machine out and turned on its back. Temp reinstall and ops checked good. Contacted Partselect for return slip, emailed immediately and sent thru post office.

Needed GE Technician to install. Partselect.com had to send a second replacement rack because the first one was defective. When the second on arrived, IT TOO WAS DEFECTIVE. After the Tech tried to install the second replacement, he was forced to remove a part from the original rusted rack in order to get the 2nd replacement to even stay in the rails of the machine. Tech was great, but the Partselect.com parts were unusable as sent.

Due to the almost zero clearance between the recirculating pump and the floor, getting the pan to line up and engage the tabs on the dishwasher frame can seem to be an impossible task. I did accomplish the task as instructed in the owners installation manual once.

However, I observed that the leak was just a drop at a time only on the deep clean mode where water recycling was in constant use during a long wash cycle. So, I recommend to slide the pan in the relative position without trying to engage the tabs and you will still accomplish the reason for the leak pan. Remember, the purpose of the Leak Pan is to protect your floor, so use it the easy way as I am.

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

Super easy repair, just removed the old latch and replaced it with the new one.

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...