GDP695SBM5TS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rick from FAIRVIEW, OK
- Parts Used:
- WD21X23498
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishes not drying and no heat other than hot tap water
Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from ANGIER, NC
- Parts Used:
- WD21X31902C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
No power, no lights, dead dishwasher
First, I watched YouTube video's a few times. Then as I was waiting for the user interface to arrive I watched some more video's. This repair isn't too difficult but requires a lot of patience. Just pay attention to what is required to get to the user interface. Also, I recommend doing this repair at a quiet time with less traffic from kids and pets and it will take about two hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from JAMESTOWN, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door did not latch, therefore would not operate
Replaced latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WG from VALLEY SPGS, CA
- Parts Used:
- WD26X23258
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dead spot in motor
Not having to screw with the hose clamps is the advantage here!
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ROSEVILLE, CA
- Parts Used:
- WD19X24829
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Replace the DW drain pump
Pretty easy repair, since I installed the DW, so knew how it went in,
turn off breaker, shut off & disconnect water, disconnect drain line into disposal, siphoned water out of bottom collection basin below sump filter.
Slid DW out from under counter & laid on it's side.
Glad I watched a YouTube video so I knew to pry open 1 of 2 crimp style hose clamps on the old drain pump, then made sense why this was a drain pump "kit" that included 4 or 5 standard band hose clamps.
turn off breaker, shut off & disconnect water, disconnect drain line into disposal, siphoned water out of bottom collection basin below sump filter.
Slid DW out from under counter & laid on it's side.
Glad I watched a YouTube video so I knew to pry open 1 of 2 crimp style hose clamps on the old drain pump, then made sense why this was a drain pump "kit" that included 4 or 5 standard band hose clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaRay from PRESCOTT, AZ
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
soap did not dispense correctly
Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- louis from ROCKTON, IL
- Parts Used:
- WD28X20164
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower rack was broken/ rusted
Just snap part in position quick to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Drew from ROACHDALE, IN
- Parts Used:
- WD28X34743
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bottom dishwasher rack had rusted prongs and a few had broken off.
Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from TOLLAND, CT
- Parts Used:
- WD08X22095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher tub was leaking
Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from STERLING, CO
- Parts Used:
- WD05X30818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dishwasher was not drying
I followed the U tube instructions already put out part select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from JUNCTION CITY, OR
- Parts Used:
- WD15X26140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
No water getting to the dishwasher
Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!