GSD2101V55WW General Electric Dishwasher - Instructions

I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy

Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!

Ordered the Drain Valve Shaft Seal and Push On Nut to make repair. Removed dishwasher from counter. Removed motor/pump assembly from dishwasher. Removed drain celenoid from pump. Removed old push on nut and old drain valve seal. Installed new seal and push nut. Replaced everything in reverse order. Amazingly no water leaks after reinstallation. Seams to be working fine so far....fingers crossed. Hoping to get a few more years out of this dishwasher.
Thank You PartSelect.

Followed the sequence from on line video provided by PartSelect. Knowing the sequence and the secret of the push on nut made the replacement simple. My dishwasher is built in therefore I pulled my dishwasher half way out to gain better access and did not need to disconnect drain or water supply. Just unplugged the power and went to work.

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

The instructions provided are very good if I had done before. My concern was getting the gasket to sit properly at the bottom where you cannot see. I removed the inside of the door (7 screws) and this made it easier to assure gasket sat properly in the track. may have cost an extra 15 minutes but worth it. If I do again I will take door apart again, however I think this is fixed and should not need attention again.

The solenoid and linkage was easy to disasemble, but getting the retainer (push on nut) off was difficult without removing the motor and pump. Once removed it was a snap. Getting the pump/motor back onto the pipes was near impossible from underneath. I had to remove the dishwasher from under the countertop to get it back correctly. I would reccomend doing this for this repair, as it made life a lot easier. Unwiring and removing the water supply line was not a problem either. WORKS AS GOOD AS NEW!

from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.

This is a very simple fix. The majority of work comes from getting the unit out of it's enclosed space so it can be worked on. Once the dishwasher is out in the open, lay it on it's side, and simply unscrew some metal clamps, pop out the bad part, replace it with the new, reattach the pieces and clamps, and start putting the unit back in place.

I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.

I'll be back to this site in the future if/when other parts on other appliances go bad.

There is nothing worse than having a knob break off when using the dishwasher. The great thing is that I was able to go on the internet and found your supply outfit. I ordered the replacement and had it to install in less than 48 hours. The knob was the right one and now I use the dishwasher again TNX

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you