GSC3500D55BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
With non-use the drain control shaft started leaking
As the washer is slightly undersized to perform correctly, following standard instructions to replace the drain valve staff seal and retaining washer I wound Teflon tape between the retaining ring and washer to slightly increase pressure on the washer and seal the opening.
Was this instruction helpful to you?
Thank you for voting!
Lower Dishwasher rack was starting to rust
The rack for my model has been discontinued so they shipped me the replacement version. The wheels on the new one are skinnier than the original model so I had to remove them and replace them with the wheels from the old rack for it to fit/roll correctly. The new wheels were a little tricky to get off as I had to use a screw driver and basically manipulate/pry apart the clamps that hold them on. The old wheels just snap on.
Was this instruction helpful to you?
Thank you for voting!
Leaking water in the shaft seal.
I follow the instruction showing in your video and the replacement was very easy. I am very please that you provided a didactic video. Now the dishwasher is working like new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
Leaking Dishwasher
Replacing the two corner baffles was the third attempt to stopping the leak. I first replaced the door seal without removing the inner door and the leak did not stop. Then I removed the inner door, reinstalled the door along the bottom and added the small seal required at the lower center portion which is separate than the longer door seal. Still leaked! Then I replaced the corner baffles and alas., the leak stopped. I would recommend that all seals be replaced at the same time. Total cost about $40.00 and can easily be done in one hour or less. I ordered the parts And they arrived remarkably in les than 24 House with regular delivery. Very pleased with Parts Select instructions and service!
Was this instruction helpful to you?
Thank you for voting!
Leaking shaft seal
There was no mention of a very slight rub of silicone for lubrication. I have always utilized this on all "O" rings with good results!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Broggie from Burlington, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill Cap Just Keep Turning, Not Locking In Place
I Just Open Door And Put Fill Cap In And Turn That It
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from walworth, NY
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pankaj from KENNESAW, GA
- Parts Used:
- WD09X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original knob broke off
After aligning the new knob shaft to the slotted hole and with a slight inward pressure, it snapped right in place
Was this instruction helpful to you?
Thank you for voting!
Leaking from left hand corner
Replaced both left and right baffle and the problem seems to be corrected. Very simple without the assistant of a professional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIN from LAS VEGAS, NV
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Silverware Basket Missing
This is erins dad. She just bought her first home and it was missing the basket. I went online found your company and ordered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Aurora, CO
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels kept coming off of the basket
Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.
Was this instruction helpful to you?
Thank you for voting!