GSD3300K55BB General Electric Dishwasher - Instructions

Just took the old rusty rack out and put the new one in its place.

Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip. , Rescrewed in the new rubber connector. ( Hint- used petrolem vasaline on the rubber connector base for a water tight fit) . Reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. Turned water back on. All worked at well.

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

It was tricky to get the old rack off. Usually you can unclip the clips closest to the front wheels to pull the rack out. However, there is an area behind one of the wheels that you can kind of release and than pull the rack out. You then have to slide out the funnel/fan piece from the middle. That piece slides/ snaps in the middle of the the new rack. Then slide the new rack in place, re attach the release used to slide oldrack out.
That is it !!

To remove the upper rack, twist the support rail end caps toward the center of the machine and slightly downward. The caps will come off and you can slide the new rack into place. Reverse the process to replace the end caps. One of mine broke and I will need to order replacements.
The original rack is no longer available. The replacement, which is the only one GE offers, has less storage space and is not as sturdy. It bends downward when full. I am very disappointed and recommend not replacing the rack unless you have no other choice.

Replaced with a new rinse aid fill cap.

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.

Just lift out the old dishrack and put in the new. Very easy and straightforward. Easy to order, unit came assembled. Happy customer.

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

I couldn't do the repair because the parts arrived a week after I left, even though I paid extra for speedy delivery. And there was ZERO customer support - the phone message said they would not answer the phone, and the email response was a generic FAQ.

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!

Old baffles lift out and new ones installed - very easy

Removed the old one from its slot and slid the new one into it.
No instructions needed.