HDA2100H55CC General Electric Dishwasher - Instructions

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

Unscrewed the old roller. But it was difficult to replace the roller as the rim of the roller would not fit into the slide mechanism and allow the screw to engage the hole. What I thought would be a 2 minute job turned out to be more like 20 minutes. I suspect there is a way to release the slide stop so that the top basket could be removed with its slide bar, but I did not see how to do that. I finally was able to "force" the screw into the hole

As the washer is slightly undersized to perform correctly, following standard instructions to replace the drain valve staff seal and retaining washer I wound Teflon tape between the retaining ring and washer to slightly increase pressure on the washer and seal the opening.

Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.

The rack for my model has been discontinued so they shipped me the replacement version. The wheels on the new one are skinnier than the original model so I had to remove them and replace them with the wheels from the old rack for it to fit/roll correctly. The new wheels were a little tricky to get off as I had to use a screw driver and basically manipulate/pry apart the clamps that hold them on. The old wheels just snap on.

I Just Open Door And Put Fill Cap In And Turn That It

No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

I follow the instruction showing in your video and the replacement was very easy. I am very please that you provided a didactic video. Now the dishwasher is working like new. Thanks.

There was no mention of a very slight rub of silicone for lubrication. I have always utilized this on all "O" rings with good results!

Replacing the two corner baffles was the third attempt to stopping the leak. I first replaced the door seal without removing the inner door and the leak did not stop. Then I removed the inner door, reinstalled the door along the bottom and added the small seal required at the lower center portion which is separate than the longer door seal. Still leaked! Then I replaced the corner baffles and alas., the leak stopped. I would recommend that all seals be replaced at the same time. Total cost about $40.00 and can easily be done in one hour or less. I ordered the parts And they arrived remarkably in les than 24 House with regular delivery. Very pleased with Parts Select instructions and service!

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.

Slide it into the arm until you hear it snap

Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.

Replaced both corner tub baffles but did not correct the problem.