GDP615HFM0DS General Electric Dishwasher - Instructions

damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...

As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.

I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!

Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.

Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!

Very easy repair. Remove wiring harness that is a simple click. Remove 2 hose clamps. Take off the old pump and install the new one. It is that simple. It is way more work to turn off the water, unscrew the dishwasher from the counter, slide the dishwasher out, turn it on it's side, then have to put it all back in, with the isulation.

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

just bolted on the new one and hooked up the hose

Took old valve assembly off and replaced with new assenbly

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

First went to U Tube to view installation instructions and location of part. It was fairly easy to replace since I had installed the unit. I was able to move the unit out enough without disconnecting any line since there was enough slack in all three connections, only shut the power off. I did use the new parts even though the older ones were not broken. The nylon pulley wheel had built up with lint causing the cable to come off.

1. Turn off the water.
2. Turn off the power to the dishwasher.
3. Pulled out the dishwasher.
4. Tilted it forward and to the side with a bowl to collect the water at the bottom.
5. Carefully laid the dishwasher on its side
6. Removed the existing pump. Make note of its orientation before removing (maybe take a picture). Disconnect the wire and loosen the 2 pipe clamps used to attach the pump. The pipe clamps were not the adjustable, reusable kind but the replacement part came with several.
7. Put the new pipe clamps on the hoses (the supply and discharge side) so they're in place.
8. Installed the replacement pump by pushing it on to the supply then the discharge hoses.
9. Move the clamps into place and tighten.
10. Reconnect the power wire.
11. Stand the dishwasher up.
12. Turn on the power and water.
13. Run a quick test to make sure it's working and doesn't leak.
14. Push it back in to place and reattach it to the cabinets.

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.