GDF530PGM0WW General Electric Dishwasher - Instructions

Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.

The dishwasher had been installed before we added 3/4 oak floor, so I could not pull the dishwasher out from under the counter. That will be a major project when the dishwasher dies.
To remove the door, I removed the two 1/4 " screws on the right and left bottom of the door. I used a box wrench since that was the only way to reach them. One had corroded due to a leak. it took some coaxing but finally came loose. The hint about opening the door 27 degrees and propping it open with two Allan wrenches through the hinge holes was very helpful. Then I lifted the door a little and gently pushed toward the counter releasing the door form the hinges. I took the door off to find a leak and found the right corner edge of the inside tub had cracked. Not sure how this happened. I cleaned and sanded the crack area and used J-B Weld to epoxy the crack. Replacing the gasket was easy. Slide out the old, slide in the new. Everything went back together smoothly. If I hadn't needed to repair the tub, the hint about opening the door all the way and sliding it out part way might have worked to change the gasket. Note. Unlike a stove door the dishwasher door is not that heavy.

I got lucky and found the diagnostic test instructions tucked inside the washer under the kick plate. From there I ran the tests on each component until I narrowed it down to the pump. The pump cost me less than local dealers. The install went well. Watched the online videos to make sure I was doing it right. Was actually very easy and saved hundreds over a service call.

All we had to do was order the top and lower racks and put them in. It was way less work and cheaper than having to put in a new dishwasher.

Took old valve assembly off and replaced with new assenbly

just bolted on the new one and hooked up the hose

I removed the old gasket and installed the new one in the same position as the one I removed. I had to feel with my fingers for the ridge to insert the gasket so that it would hold. I must admit that I was skeptical that it would work (the old one didn't even seem very damaged). I ran a cycle and there was no more leaking. We've been using the dishwasher ever since with no issues of leakage.

Very satisfied customer.

Very easy repair. Remove wiring harness that is a simple click. Remove 2 hose clamps. Take off the old pump and install the new one. It is that simple. It is way more work to turn off the water, unscrew the dishwasher from the counter, slide the dishwasher out, turn it on it's side, then have to put it all back in, with the isulation.

The installation is fairly straightforward, basically one plug in electrical connection and two plumbing connections. The smaller of the two plumbing connections can be tricky because of the hose clamp... The original clamps are one time use crimp style. The replacements are standard hose clamps, which means the section where the tension mechanism is, is a bit wider than the clamp itself... This can cause the rubber collar on the dishwasher to slide off/separate from the pump part itself when tightening the hose clamp. If you are careful and align things just right, it will work like a charm. The best advice I have is to take your time and make sure the connections are snug without being too tight, otherwise it could leak and/or something else could break.

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...

As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.

I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

1. Turn off the water.
2. Turn off the power to the dishwasher.
3. Pulled out the dishwasher.
4. Tilted it forward and to the side with a bowl to collect the water at the bottom.
5. Carefully laid the dishwasher on its side
6. Removed the existing pump. Make note of its orientation before removing (maybe take a picture). Disconnect the wire and loosen the 2 pipe clamps used to attach the pump. The pipe clamps were not the adjustable, reusable kind but the replacement part came with several.
7. Put the new pipe clamps on the hoses (the supply and discharge side) so they're in place.
8. Installed the replacement pump by pushing it on to the supply then the discharge hoses.
9. Move the clamps into place and tighten.
10. Reconnect the power wire.
11. Stand the dishwasher up.
12. Turn on the power and water.
13. Run a quick test to make sure it's working and doesn't leak.
14. Push it back in to place and reattach it to the cabinets.

Don't remove the door! Unscrew the bolts at each lower corner of the door(this is how the door is attached to the hinges so it is now free). Then open the door fully and slowly pull the door toward you a few inches. This slides the door up the hinges and allows just enough room to slide the old gasket out and and slide the new one in. Then slide the door back down the hinges(pushing it away from you, back into place). Then simply close the door and reinstall the bolts at the bottom corners and all done! I watched several videos and believe me, removing the door to replace this gasket does nothing but turn and small quick repair into a large lengthy one.