GDT535PGM0WW General Electric Dishwasher - Instructions

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Took it out of the box and set rollers on track
rolled in place ALL DONE

Twist counter clockwise to remove clockwise to install

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Release DW from cabinet and pull out, Unplug power.
Remove kick plate and unplug door cable.
Open door about 6 inches and using socket back out 2 bolts at bottom of door corners.
Pull door up off hinges about 4 inches and slide old gasket out and install new gasket in place.
Reset door on hinges and reinstall bolts.
Plug door cable in and reattach kick plate and plug power cable in.
Push DW back in place and attach to cabinet and adjust kick plate

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Replaced gasket with a new one before further problems occurred. Got to get it in but it was relatively easy to place and snap in just make sure it fits on the right place where gasket inside meets ridges on door so it will be on properly for proper fit.

Some of these other instructions may be for other models. This is specifically for GDT530PGD2BB, which doesn't present screws on the inner side of the door.

I'm extremely reluctant to do anything more than the repair at hand, so I didn't move the dishwasher out of its recessed cabinet, which would make the repair easier. I also did not remove the connector plug from the dishwasher to the door, since there was enough slack to do the repair without this step.

1. Turn off power to the dishwasher.

2. Under the bottom of the door, there are two 1/4" hex screws that can be removed with a small socket wrench, or if you moved the dishwasher out, you can tip it over slightly and get at these screws with a Phillips screwdriver.

3. With those out, you can open the door flat and slide it off it's hinges *just a little bit*. You need maybe an inch or so clearance to slide the old gasket out and slide the new one in. I had to use pliers to remove the old, very damaged gasket, but the new one easily slid into place.

4. Were you able to just move the door out a bit without removing it totally from the hinges? Great! Slide it back, put those screws in the bottom again, and you've done it! Probably in minutes!

5. Or, you could be like me and accidentally lift the door too far and have one of the hinges pop out. If I had someone helping me, it would have taken half a minute to put the door back on its hinges, but I was by myself, so I had to finagle something to keep the hinges open (two screwdrivers wedged handle first), so I could slide the door back on the hinges. That took me about 10 minutes. ¯\_(?)_/¯

Good luck!

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Got the seal, read the reviews to see how to do it, Take out the two bottom screws ,easy enough. pull the door up ,pull out seal replace new one. Easy enough, but know one said don't pull the door up too high , I did, could not get it back down to save my soul. Needles to say had to buy a new dishwasher. that sucked have the new seal gasket if anybody needs one