GDF630PMM3ES General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Josef from MT CARMEL, TN
- Parts Used:
- WD08X21894, WD08X10092
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking under door
Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FAIRFIELD, CT
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holes in old dishwasher basket
The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BYRON CENTER, MI
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty bottom dishwasher basket
Slid out old part and slid in new part!!! Yup that easy!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from ASHEVILLE, NC
- Parts Used:
- WD19X24829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dishwasher stopped draining.
We I installed a new dishwasher pump. It was simple and easy. I did it myself. My husband removed the clamps holding the dishwasher in the cabinet. Then he turned it in it's side and I replaced the old pump for an identical one that I ordered from this site. Easy peasy, took all of 15 minutes. You've got this. Don't call a repair man and pay $300 or buy a new dishwasher and pay $800. This repair was $63. If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from CHESAPEAKE, VA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating element broke off and burned a hole in rubber tube, leaking water.
Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from MASON, OH
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty Lower Rack
Removed lower rack, slid in new Rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Praveen from Monroe Township, NJ
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
as better as it gets
the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Plainfield, IL
- Parts Used:
- WD08X21894
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Worn bottom door seal
Easy repair, googled a how-to video and I was surprised how well i was able to follow instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lesa from BETHALTO, IL
- Parts Used:
- WD13X10071
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishwasher would not know door was closed
Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from TOPOCK, AZ
- Parts Used:
- WD19X24829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Water would not drain
The repair was just like the video that the agent sent me. And while I had the unit out of the cabinet I installed a part I have had for months which I ordered before I realized I had to take the unit out of the cabinet: the part was the seal for the bottom of the door. I recommend if you are ordering a pump order this part too an it is easy to install if you already have the dishwasher out of the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from FT WASHINGTON, MD
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original rack was deteriorated and staining dishes.
Replaced old rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Brambleton, VA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replace the middle flatware basket
So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from cherry hill, NJ
- Parts Used:
- WD28X34744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lower try rusting out
Part was incorrect Compare that to GE site saying number on both ports to different parts try to return was half the course of what I paid ridiculous So apparently I'm stuck with it Check GE site you'll see the port is different from what your sound but the numbers are exactly the same No clips to support the utensil tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from OAK RIDGE, NC
- Parts Used:
- WD35X10393
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher made rhythmic, thumping sound during wash cycle
This was so easy! Our 4 year-old dishwasher began making a repetitive, clunking noise during wash cycle, and I deducted that it was the spray arms. I tried to rinse out old
spray arms, checked for clogs, and made sure they were installed correctly. The sound persisted, so I ordered replacement part (wash arm kit). I removed old spray arms and attached new ones. Problem solved and dishwasher is quiet again!
spray arms, checked for clogs, and made sure they were installed correctly. The sound persisted, so I ordered replacement part (wash arm kit). I removed old spray arms and attached new ones. Problem solved and dishwasher is quiet again!
Was this instruction helpful to you?
Thank you for voting!