PDW9900NW General Electric Dishwasher - Instructions

Removed and replaced all rack wheels with new wheels and wheel axles. All I needed was new axles, as they are new and better, and solved the problem of the wheel falling off. G.E. should offer customers with this problem, new wheel axles at no charge, as they are very easy to exchange. The original axle was a bad design.

Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

The entire flat side of the end cap, (with the cutout latch), goes on the outside of the guide bar. It took less than 15 seconds to insert. It took about 30 minutes of searching for videos and playing around with the part to figure this out. A simple diagram would have been helpful.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.

Installed new roller which where larger than the original rollers. I believe these larger rollers will stop rack from slipping down near heating coils.
The new rollers snapped on with very litlle effort.

HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!

Followed instructions on how-to video on website on how to remove and replace lower spray arm.

Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.

Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.

The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.

This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.

The repair is just a couple of minutes job. All I had to do was to pop the wheel axle in the new wheels, remove the old wheels and put the new ones in. The wheel axles on the original one, were like clasps. All one needs to do is to pull the clasp to one side and slide the wheel out. The new one, just needs to be pushed in. In my case, I could have just swapped out the axles, but decided to change the whole set anyway.

It was sooo easy, I can't believe I took so long to get these new rollers and studs. Shipment arrived in 2 days, I removed those old melted wheels, through them away and installed the new ones, took me less than 10 minutes, it was painless, no tools needed. I did follow a tip from a buyer that was to attach the studs to the wheels prior attaching them to the lower rack and it was a very usefull tip. Do that! Now my dishwasher is like new again. Great shopping experience, Thank you!