GSC3400GW General Electric Dishwasher - Instructions

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

Removed the lower rack and installed new wheels with clips

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,

turn wand counter clockwise until it's out,replace it with the new one.DON'T OVERTIGHTEN!

i removed the old power tower with a regular plumbers pliers spining SLOWLY and firmly but no too firm until it broke loose and unscrewed. I reintalled the new tower oppisite how i removed it being carefull not to overtighten. all is well. it was very ez, so much in fact that my wife thought she was going to be able to read a book waiting for me "all afternoon" to fix it! Bad news, I had to take her shopping!

i was impressed with the ease and speed of normal delivery of this part. this is a quality company. JS

Went to repair parts on troubleshooting and found check valve assembly to be most common problem. Went to parts diagram to locate assembly and found it somewhat confusing as to exact location. Ordered part(s) on percentage as the problem. Received part next day (great)! Pulled dishwasher out and found I did NOT need to do so to replace check valve which is replaced without having to remove dishwasher. The gasket replacement was not necessary as it seals sump area from bottom of dishwasher and not the valve as it appears on the parts diagram. It took about 2 minutes to replace valve itself and it was the cause of the problem.

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

I had a slow drip under the dish washer that originated from the solenoid shaft. The replacement o ring fixed it up. While I had it pulled out I replaced all the door seals and top rack rollers.

I ordered the parts on a Thursday evening and received them on Friday. WOW now that's fast! The parts came from Illinois and I live in Indiana so that might have helped but I was very surprised and glad for the quick service. I would defiantly order from Parts Select again. Thank you!

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.

Removed seven screws that held the inside panel to door. removed inside panel to work area and cleaned. After carefully observing the position of the old gasket, it was easily removed and the new one but in its place. Replaced the door being careful toalign the handle before tightly securing all seven screws. Repair worked, no more leak.