GHDA674NB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- andrew from galveston, TX
- Parts Used:
- WD21X10224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
wouldnt start and lights flickered
pulled switches flicked leaver worked when itwanted to and not every time. I removed then shorted then rechecked everthing worked. got on line ordered parts good price fast service fixed 30 min when they came in saved money.Thank God! 20.00 fix instead of 200.00 +
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Julesburg, CO
- Parts Used:
- WD08X10059
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dishwasher was leaking at the bottom of the door
I removed the eight screws around the door. Slid the inside of the door up just a little ways pulled the rubber gasket straight out to the right of the door, watched to see what direction it was attached slid the other one in on the track you can't get it wrong. Put the panel to the door in place and put the screws back. Very easy!! Thank You, Sandra Salyards
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from chesterton, IN
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
water inlet valve wore out would not work
got replacement valve from part select and works like new this dish wash er is 24 years old. believe it or not did the job with pair of pliers and screw driver. used pliers to take off clamp and screw driver to take out 2 screws and replaced the valve the same way in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Carver, MA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
There was a thumping noise when we started the dishwasher
We googled, "thumping noise" when running the dishwasher and one of the possible reasons was the Lower Spray Arm. So, we purchased a new one and replaced it. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stewart from Frisco, TX
- Parts Used:
- WD08X10059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lower door seal was leaking
Removed the screws holding the inner door panel from the door. I just flipped it over and used the weight of the removed panel to hold down the spring loaded door. I took note of the position of the old seal and then removed it. I cleaned away all of the accumulated soap residue. The new seal was positioned by just sliding it into place. I flipped the door panel over and replaced all of the attaching screws. Don't try to press the new seal into place. Slide it onto the lip of the door panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Windermere, FL
- Parts Used:
- WD01X10410, WD02X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Upper spray arm bearing and screw missing to hold spray arm
The diagram was very helpful to make identifying what parts were needed. Very prompt in sending the parts,in less than 24 hrs! Would highly recommend ordering from here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cameron from Yorktown, VA
- Parts Used:
- WD12X10401, WD21X10224
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not power-up
I troubleshot the problem down to the 2 small interlock switches and the cover that protects them. They are directly behind the the door handle mechanism. The switches were shaky and the cover was bowed out. Ordered the 2 switches and the cover, next day mail. The delivery charges were more than the parts. Easy fix. Saved $90 for the repairman visit plus what ever he gets for his time and his cost for the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Garner, NC
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate in bottom of the basket broken
Removed old basket, put in recycle bin, placed new basket in dish washer. The damage to the original basket was my fault. I now know not to drop heavy knives point down into the basket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Nespelem, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Wouldn't clean upper rack, not enough water
Checked the water supply to the inlet valve - OK, pulled the filler hose from the outlet side of the valve and checked flow in wash cycle. Results, less than 1/2 gallon. Checked your website, found 94% sucess rate by replacing the valve, so I ordered one. It took about 10 minutes to install with a nut driver, 6" adjustable to connect water supply, and plier to hold outlet clamp open to install it; now we look forward to dirty dishes rather than dumping water into the machine it takes care of itself and we once again get sparkly cups andglasses of the top rack. OU- Rah!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from The Villages, FL
- Parts Used:
- WD12X10206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse cap had fallen on heating element and melted
The part was extremely easy to find on the web site and the order was placed easily. This was very simple and quick to replace. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Indio, CA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
removed old silverware basket
installed new silverware basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Waterford, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bad wheel
Pull rack out put wheel on put rack back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith W. from Topeka, KS
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rear rack wheels
Quick and easy...a 7 yr old could have done it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Spring, TX
- Parts Used:
- WD12X10352, WD22X10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
My dishes were not getting cleaned
The problem started with my dishes slowly becoming less and less clean wash after wash. To diagnose the problem, I turned on the dishwasher and waited for the clean cycle to start. After it did I opened the door and peaked inside to see the top and bottom spray arms were moving but not the middle one. I took it out and stuck it under the faucet to make sure it wasn't clogged and everything seemed good. So after much deliberations, I decided that it must be the pump, so I replaced it. NOPE! That was costly. I then read something on the internet about how the middle arm has two jets on the bottom so I checked mine and sure enough, they were clogged. I tried to clean it but I could not get the junk out. So I decided to but the spray arm and the arm holder(because I damaged it)and now my dishwasher runs great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Naples, FL
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Torn gasket
Piece of cake! Very easy. Thanks for quick shipment. Appreciate it.
Was this instruction helpful to you?
Thank you for voting!