GSD3810Z04AA General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GREGORY from WARNER ROBINS, GA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Top spindle of lower spray arm was broken off
Unscrewed bottom of spray arm support assembly counterclockwise by hand for removal. Inserted new part and screwed it in clockwise by hand for installation. Worked perfectly. Video was helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from ST LOUIS PARK, MN
- Parts Used:
- WD24X10018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishes were not coming out clean and water was standing after the wash cycle was complete.
Removed filter/screen by unscrewing 2 screws with a nut driver and then unscrewed the old Piston and Nut assembly and simply screwed in the new part. Problem solved and my dishes are much cleaner and the water is draining out completely. Easy fix for this frustrating problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Broggie from Burlington, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill Cap Just Keep Turning, Not Locking In Place
I Just Open Door And Put Fill Cap In And Turn That It
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Medford, OR
- Parts Used:
- WD28X31818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old Rack Was Losing Plastic Coating And Was Rusting
I removed the end caps on the two side tracks using pliers. I pulled out the old rack and inserted the new one. I replaced the end caps and I was done. It was that simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDY from COLORADO SPRINGS, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Inch Of Clean Water Left In Machine After Each Cycle
First let me say, it's so easy even a caveman can do it. I removed the water out of the bottom. Then I removed the cover in the very back of the machine with a wrench. As soon as I did that, I could see the piston. Next, I twisted the white piston out with my fingers (this was the hardest part). I could see the piston had partially disintigrated. I ordered a new one, had it delivered in a few days, and put it all back in reverse. It took minutes. Thanks to the guy that posted his story, I was able to fix mine for $18.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ohlen from Springfield, SC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher wouldn't drain completely between cycles, causing it to overflow.
First I opened the dishwasher and removed the lower basket. Next I removed the 4 screws that hold the food filter plate in place at the back of the tub. Then I unscrewed the Piston/Check Valve assembly counterclockwise, located at the back center of the tub, by hand. I replaced the old part with the new one and reinstalled the filter plate. I ran a rinse cycle to verify that that all of the water was purged. Finally, I reinstalled the lower basket and resumed using my dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from Allendale, MI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher would not drain completly after each cycle
removed screen at back of dishwasher from the inside. Twisted piston & nut assembly out by hand and replaced with new one. Very, very simple. Dishwasher works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Kansas City, MO
- Parts Used:
- WD28X31818
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
rack worn out and putting rust on dishes
took end caps off (one broke) slid in new disk rack and put caps back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonita from Alexandria, VA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
End of cycle water in bottom of nDishwasher
Removed screen bottom rear andfound a plunger type part, unscrewed plunger and found it was distressed around it and did not close of a tight seal. Placed new part into location and dishwasher now proforms perfect...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clyde from DUNCANNON, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
water would not pump out of machine
I looked at your web sight and saw how to repair dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett from Sound Beach, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Pump/Motor leaking at shaft
This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from longmont, CO
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
leak between motor and pump housing
repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Key Biscayne, FL
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water would not drain out and keep filling up sprayers work
Your video doesn't include disconnecting water supply disconnecting electrical and disconnecting drain hose but after all that the repair to change the solenoid was a easy task but the problem was not solved so I TRIED . thanks Robert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buddy from Danville, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Pump seal was leaking
I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- g from el monte, CA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
pump unit does not work, motor stucked
after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.
Was this instruction helpful to you?
Thank you for voting!